Combustion analysis of a CI engine performance using waste cooking biodiesel fuel with an artificial neural network aid

Article

Najafi, Gholamhassan, Ghobadian, Barat, Yusaf, Talal and Rahimi, Hadi. 2007. "Combustion analysis of a CI engine performance using waste cooking biodiesel fuel with an artificial neural network aid." American Journal of Applied Sciences. 4 (10), pp. 756-764.
Article Title

Combustion analysis of a CI engine performance using waste cooking biodiesel fuel with an artificial neural network aid

ERA Journal ID1161
Article CategoryArticle
AuthorsNajafi, Gholamhassan (Author), Ghobadian, Barat (Author), Yusaf, Talal (Author) and Rahimi, Hadi (Author)
Journal TitleAmerican Journal of Applied Sciences
Journal Citation4 (10), pp. 756-764
Number of Pages9
Year2007
Place of PublicationUnited States
ISSN1546-9239
1554-3641
Web Address (URL)http://www.scipub.org/fulltext/ajas/ajas410756-764.pdf
Abstract

[Abstract]: A comprehensive combustion analysis has been conducted to evaluate the performance of a
commercial DI engine, water cooled two cylinders, in-line, naturally aspirated, RD270 Ruggerini
diesel engine using waste vegetable cooking oil as an alternative fuel. In order to compare the brake
power and the torques values of the engine, it has been tested under same operating conditions with
diesel fuel and waste cooking biodiesel fuel blends. The results were found to be very comparable. The
properties of biodiesel produced from waste vegetable oil was measured based on ASTM standards.
The total sulfur content of the produced biodiesel fuel was 18 ppm which is 28 times lesser than the
existing diesel fuel sulfur content used in the diesel vehicles operating in Tehran city (500 ppm). The
maximum power and torque produced using diesel fuel was 18.2 kW and 64.2 Nm at 3200 and 2400
rpm respectively. By adding 20% of waste vegetable oil methyl ester, it was noticed that the maximum
power and torque increased by 2.7 and 2.9% respectively, also the concentration of the CO and HC
emissions have significantly decreased when biodiesel was used. An artificial neural network (ANN)
was developed based on the collected data of this work. Multi layer perceptron network (MLP) was
used for nonlinear mapping between the input and the output parameters. Different activation functions
and several rules were used to assess the percentage error between the desired and the predicted values. The results showed that the training algorithm of Back Propagation was sufficient enough in predicting the engine torque, specific fuel consumption and exhaust gas components for different engine speeds and different fuel blends ratios. It was found that the R2 (R: the coefficient of determination) values are 0.99994, 1, 1 and 0.99998 for the engine torque, specific fuel consumption,CO and HC emissions, respectively.

Keywordsalternative fuel; biodiesel-diesel blends; artificial neural network
ANZSRC Field of Research 2020400402. Chemical and thermal processes in energy and combustion
400201. Automotive combustion and fuel engineering
Public Notes

File reproduced in accordance with the copyright policy of the publisher/author.

Byline AffiliationsTarbiat Modares University, Iran
Permalink -

https://research.usq.edu.au/item/9y2v1/combustion-analysis-of-a-ci-engine-performance-using-waste-cooking-biodiesel-fuel-with-an-artificial-neural-network-aid

Log in to edit

Download files

  • 3526
    total views
  • 2329
    total downloads
  • 3
    views this month
  • 0
    downloads this month

Export as

Related outputs

Correction: Algayyim et al. Sugarcane Biomass as a Source of Biofuel for Internal Combustion Engines (Ethanol and Acetone-Butanol-Ethanol): A Review of Economic Challenges. Energies 2022, 15, 8644
Algayyim, Sattar Jabbar Murad, Yusaf, Talal, Hamza, Naseer H., Wandel, Andrew P., Fattah, I. M. Rizwanul, Laimon, Mohamd and Rahman, S. M. Ashrafur. 2024. "Correction: Algayyim et al. Sugarcane Biomass as a Source of Biofuel for Internal Combustion Engines (Ethanol and Acetone-Butanol-Ethanol): A Review of Economic Challenges. Energies 2022, 15, 8644 ." Energies. 17 (14). https://doi.org/10.3390/en17143521
Revolutionizing procurement: Unveiling next-gen supplier strategies in UAE's oil & gas sector
Alhammadi, Ali, Yusaf, Talal, Soar, Jeffrey, Ali, Bashar Mahmood, Kadirgama, Kumaran and Yousif, Belal F. 2024. "Revolutionizing procurement: Unveiling next-gen supplier strategies in UAE's oil & gas sector." The Extractive Industries and Society. 17. https://doi.org/10.1016/j.exis.2024.101428
Influence of Natural Gas and Hydrogen Properties on Internal Combustion Engine Performance, Combustion, and Emissions: A Review
Algayyim, Sattar Jabbar Murad, Saleh, Khalid, Wandel, Andrew P, Fattah, Islam Md Rizwanul, Yusaf, Talal and Alrazen, Hayder A.. 2024. "Influence of Natural Gas and Hydrogen Properties on Internal Combustion Engine Performance, Combustion, and Emissions: A Review." Fuel: the science and technology of fuel and energy. 632. https://doi.org/10.1016/j.fuel.2023.130844
Redefining procurement paradigms: A critical review of buyer-supplier dynamics in the global petroleum and natural gas industry
Alhammadi, Ali, Soar, Jeffrey, Yusaf, Talal, Ali, Bashar Mahmood and Kadirgama, Kumaran. 2023. "Redefining procurement paradigms: A critical review of buyer-supplier dynamics in the global petroleum and natural gas industry." The Extractive Industries and Society. 16. https://doi.org/10.1016/j.exis.2023.101351
Sugarcane Biomass as a Source of Biofuel for Internal Combustion Engines (Ethanol and Acetone-Butanol-Ethanol): A Review of Economic Challenges
Algayyim, Sattar Jabbar Murad, Yusaf, Talal, Hamza, Naseer H., Wandel, Andrew P., Fattah, I. M. Rizwanul, Laimon, Mohamd and Rahman, S. M. Ashrafur. 2022. "Sugarcane Biomass as a Source of Biofuel for Internal Combustion Engines (Ethanol and Acetone-Butanol-Ethanol): A Review of Economic Challenges." Energies. 15 (22), pp. 1-17. https://doi.org/10.3390/en15228644
Experimental Study on the Efficiency Improvement of Flat Plate Solar Collectors Using Hybrid Nanofluids Graphene/Waste Cotton
Mahamude, Abu Shadate Faisal, Harun, Wan Sharuzi Wan, Kadirgama, Kumaran, Ramasamy, Devarajan, Farhana, Kaniz, Saleh, Khalid and Yusaf, Talal. 2022. "Experimental Study on the Efficiency Improvement of Flat Plate Solar Collectors Using Hybrid Nanofluids Graphene/Waste Cotton." Energies. 15 (7), pp. 1-27. https://doi.org/10.3390/en15072309
System dynamics modelling to assess the impact of renewable energy systems and energy efficiency on the performance of the energy sector
Laimon, Mohamd, Mai, Thanh, Goh, Steven and Yusaf, Talal. 2022. "System dynamics modelling to assess the impact of renewable energy systems and energy efficiency on the performance of the energy sector." Renewable Energy. 193, pp. 1041-1048. https://doi.org/10.1016/j.renene.2022.05.041
A systems thinking approach to address sustainability challenges to the energy sector
Laimon, M., Yusaf, Talal, Mai, T., Goh, S. and Alrefae, Waleed. 2022. "A systems thinking approach to address sustainability challenges to the energy sector." International Journal of Thermofluids. 15, pp. 1-13. https://doi.org/10.1016/j.ijft.2022.100161
Effects of exhaust gas recirculation (EGR) on a diesel engine fuelled with palm-biodiesel
Yasin, Mohd Hafizil Mat, Mamat, Rizalman, Yusop, Ahmad Fitri, Paruka, Perowansa, Yusaf, Talal and Najafi, Gholamhassan. 2015. "Effects of exhaust gas recirculation (EGR) on a diesel engine fuelled with palm-biodiesel." Energy Procedia. 75, pp. 30-36. https://doi.org/10.1016/j.egypro.2015.07.131
Development of micro-scale biomass-fuelled CHP system using stirling engine
Arashnia, Ilva, Najafi, Gholamhassan, Ghobadian, Barat, Yusaf, Talal, Mamat, Rizalman and Kettner, Maurice. 2015. "Development of micro-scale biomass-fuelled CHP system using stirling engine." Energy Procedia. 75, pp. 1108-1113. https://doi.org/10.1016/j.egypro.2015.07.505
Optimization of combustion in micro combined heat and power (mCHP) system with the biomass-Stirling engine using SiO2 and Al2O3 nanofluids
Najafi, G., Hoseini, S. S., De Goey, L. P. H. and Yusaf, Talal. 2020. "Optimization of combustion in micro combined heat and power (mCHP) system with the biomass-Stirling engine using SiO2 and Al2O3 nanofluids." Applied Thermal Engineering. 169 (114936), pp. 1-9. https://doi.org/10.1016/j.applthermaleng.2020.114936
Analysis of Particulate Matter (PM) Emissions in Diesel Engines Using Palm Oil Biodiesel Blended with Diesel Fuel
Yusop, Ahmad Fitri, Mamat, Rizalman, Yusaf, Talal, Najafi, Gholamhassan, Yasin, Mohd Hafizil Mat and Khathri, Akasyah Mohd. 2018. "Analysis of Particulate Matter (PM) Emissions in Diesel Engines Using Palm Oil Biodiesel Blended with Diesel Fuel." Energies. 11 (5), pp. 1-25. https://doi.org/10.3390/en11051039
Alcohol and ether as alternative fuels in spark ignition engine: A review
Awad, Omar I., Mamat, R., Ali, Obed M., Sidik, N. A. C., Yusaf, T., Kadirgama, K. and Kettner, Maurice. 2018. "Alcohol and ether as alternative fuels in spark ignition engine: A review." Renewable and Sustainable Energy Reviews. 82 (Part 3), pp. 2586-2605. https://doi.org/10.1016/j.rser.2017.09.074
Ailanthus altissima (tree of heaven) seed oil: Characterisation and optimisation of ultrasonication-assisted biodiesel production
Hoseini, S. S., Najafi, G., Ghobadian, B., Mamat, R., Ebadi, M. T. and Yusaf, Talal. 2018. "Ailanthus altissima (tree of heaven) seed oil: Characterisation and optimisation of ultrasonication-assisted biodiesel production." Fuel: the science and technology of fuel and energy. 220, pp. 621-630. https://doi.org/10.1016/j.fuel.2018.01.094
Economic and Environmental Impact of Energy Saving in Healthcare Buildings
Garcia-Sanz-Calcedo, Justo, Al-Kassir, Awf and Yusaf, Talal. 2018. "Economic and Environmental Impact of Energy Saving in Healthcare Buildings." Applied Sciences. 8 (3), pp. 1-13. https://doi.org/10.3390/app8030440
The effect of inlet temperature and spark timing on thermo-mechanical, chemical and the total exergy of an SI engine using bioethanol-gasoline blends
Kiani, Mostafa Kiani Deh, Rostami, Sajad, Eslami, Maryam, Yusaf, Talal and Sendilvelan, Subramanian. 2018. "The effect of inlet temperature and spark timing on thermo-mechanical, chemical and the total exergy of an SI engine using bioethanol-gasoline blends." Energy Conversion and Management. 165, pp. 344-353. https://doi.org/10.1016/j.enconman.2018.03.066
An Experimental Technology of Drying and Clean Combustion of Biomass Residues
Al-Kassir, Awf, Coelho, Pedro, Garcia-Sanz-Calcedo, Justo, Moral, Francisco J., Al-Karany, Raul Kassir and Yusaf, Talal. 2018. "An Experimental Technology of Drying and Clean Combustion of Biomass Residues." Applied Sciences. 8 (6), pp. 1-10. https://doi.org/10.3390/app8060905
The Effects of Camelina 'Soheil' as a Novel Biodiesel Fuel on the Performance and Emission Characteristics of Diesel Engine
Hoseini, Seyed Salar, Najafi, Gholamhassam, Ghobadian, Barat, Yusaf, Talal and Ebadi, Mohammad Taghi. 2018. "The Effects of Camelina 'Soheil' as a Novel Biodiesel Fuel on the Performance and Emission Characteristics of Diesel Engine." Applied Sciences. 8 (6), pp. 1-20. https://doi.org/10.3390/app8061010
Experimental and numerical analysis of flow and heat transfer characteristics of EGR cooler in diesel engine
Hoseini, S. S., Najafi, G., Ghobadian, Barat and Yusaf, Talal. 2018. "Experimental and numerical analysis of flow and heat transfer characteristics of EGR cooler in diesel engine." Applied Thermal Engineering. 140, pp. 745-758. https://doi.org/10.1016/j.applthermaleng.2018.05.058
An overview of marine macroalgae as bioresource
Sudhakar, K., Mamat, R., Samykano, M., Azmi, W. H., Ishak, W. F. W. and Yusaf, Talal. 2018. "An overview of marine macroalgae as bioresource." Renewable and Sustainable Energy Reviews. 91, pp. 165-179. https://doi.org/10.1016/j.rser.2018.03.100
Novel environmentally friendly fuel: The effects of nanographene oxide additives on the performance and emission characteristics of diesel engines fuelled with Ailanthus altissima biodiesel
Hoseini, S. S., Najafi, G., Ghobadian, B., Mamat, R., Ebadi, M. T. and Yusaf, Talal. 2018. "Novel environmentally friendly fuel: The effects of nanographene oxide additives on the performance and emission characteristics of diesel engines fuelled with Ailanthus altissima biodiesel." Renewable Energy. 125, pp. 283-294. https://doi.org/10.1016/j.renene.2018.02.104
Characterization of biodiesel production (ultrasonic-assisted) from evening-primroses (Oenothera lamarckiana) as novel feedstock and its effect on CI engine parameters
Hoseini, S. S., Najafi, G., Ghobadian, B., Mamat, R., Ebadi, M. T. and Yusaf, Talal. 2019. "Characterization of biodiesel production (ultrasonic-assisted) from evening-primroses (Oenothera lamarckiana) as novel feedstock and its effect on CI engine parameters." Renewable Energy. 130, pp. 50-60. https://doi.org/10.1016/j.renene.2018.06.042
The Impacts of Water Pricing and Non-Pricing Policies on Sustainable Water Resources Management: A Case of Ghorveh Plain at Kurdistan Province, Iran
Asaadi, Mohammad Ali, Mortazavi, Seyed Abolghasem, Zamani, Omid, Najafi, Gholam Hassan, Yusaf, Talal and Hoseini, Seyed Salar. 2019. "The Impacts of Water Pricing and Non-Pricing Policies on Sustainable Water Resources Management: A Case of Ghorveh Plain at Kurdistan Province, Iran." Energies. 12 (14), pp. 1-16. https://doi.org/10.3390/en12142667
Optimization of an Ultrasonic-Assisted Biodiesel Production Process from One Genotype of Rapeseed (TERI (OE) R-983) as a Novel Feedstock Using Response Surface Methodology
Almasi, Sara, Ghobadian, Barat, Najafi, Gholam Hassan, Yusaf, Talal, Soufi, Masoud Dehghani and Hoseini, Seyed Salar. 2019. "Optimization of an Ultrasonic-Assisted Biodiesel Production Process from One Genotype of Rapeseed (TERI (OE) R-983) as a Novel Feedstock Using Response Surface Methodology." Energies. 12 (14), pp. 1-14. https://doi.org/10.3390/en12142656
Performance Investigation of Solar ORC Using Different Nanofluids
Loni, Reyhaneh, Najafi, Gholamhassan, Asli-Ardeh, Ezzatollah Askari, Ghobadian, Barat, Le Roux, Willem G. and Yusaf, Talal. 2019. "Performance Investigation of Solar ORC Using Different Nanofluids." Applied Sciences. 9 (15), pp. 1-23. https://doi.org/10.3390/app9153048
Performance and emission characteristics of a CI engine using nano particles additives in biodiesel-diesel blends and modeling with GP approach
Ghanbari, M., Najafi, G., Ghobadian, B., Yusaf, T., Carlucci, A. P. and Kiani Deh Kiani, M.. 2017. "Performance and emission characteristics of a CI engine using nano particles additives in biodiesel-diesel blends and modeling with GP approach." Fuel: the science and technology of fuel and energy. 202, pp. 699-716. https://doi.org/10.1016/j.fuel.2017.04.117
Performance Assessment of a Solar Dryer System Using Small Parabolic Dish and Alumina/Oil Nanofluid: Simulation and Experimental Study
Arkian, Amir Hossein, Najafi, Gholamhassan, Gorjian, Shiva, Loni, Reyhaneh, Bellos, Evangelos and Yusaf, Talal. 2019. "Performance Assessment of a Solar Dryer System Using Small Parabolic Dish and Alumina/Oil Nanofluid: Simulation and Experimental Study." Energies. 12 (24), pp. 1-22. https://doi.org/10.3390/en12244747
Effects of biodiesel fuel obtained from Salvia macrosiphon oil (ultrasonic-assisted) on performance and emissions of diesel engine
Hoseini, S. S., Najaf, G., Ghobadian, B., Rahimi, A., Yusaf, Talal, Mamat, Rizalman, Sidik, N. A. C. and Azmi, W. H.. 2017. "Effects of biodiesel fuel obtained from Salvia macrosiphon oil (ultrasonic-assisted) on performance and emissions of diesel engine." Energy. 131, pp. 289-296. https://doi.org/10.1016/j.energy.2017.04.150
Effects of physicochemical properties of biodiesel fuel blends with alcohol on diesel engine performance and exhaust emissions: A review
Zaharin, M. S. M, Abdullah, N. R., Najafi, G., Sharudin, H. and Yusaf, T.. 2017. "Effects of physicochemical properties of biodiesel fuel blends with alcohol on diesel engine performance and exhaust emissions: A review." Renewable and Sustainable Energy Reviews. 79, pp. 475-493. https://doi.org/10.1016/j.rser.2017.05.035
Analysis of the Average Annual Consumption of Water in the Hospitals of Extremadura (Spain)
Garcia-Sanz-Calcedo, Justo, Lopez-Rodriguez, Fernando, Yusaf, Talal and Al-Kassir, Awf. 2017. "Analysis of the Average Annual Consumption of Water in the Hospitals of Extremadura (Spain)." Energies. 10 (4), pp. 1-10. https://doi.org/10.3390/en10040479
Dependence of the Microporosity of Activated Carbons on the Lignocellulosic Composition of the Precursors
Roman, Silvia, Ledesma, Beatriz, Alvarez-Murillo, Andres, Al-Kassir, Awf and Yusaf, Talal. 2017. "Dependence of the Microporosity of Activated Carbons on the Lignocellulosic Composition of the Precursors." Energies. 10 (4), pp. 1-11. https://doi.org/10.3390/en10040542
Treatment of Slaughterhouse Waste Water Mixed with Serum from Lacteal Industry of Extremadura in Spain to Produce Clean Energy
Marcos, A. C., Al-Kassir, A., Cuadros, Francisco and Yusaf, Talal. 2017. "Treatment of Slaughterhouse Waste Water Mixed with Serum from Lacteal Industry of Extremadura in Spain to Produce Clean Energy." Energies. 10 (6), pp. 1-15. https://doi.org/10.3390/en10060765
Response surface methodology (RSM) based multi-objective optimization of fusel oil-gasoline blends at different water content in SI engine
Awad, Omar I., Mamat, R., Ali, Obed M., Azmi, W. H., Kadirgama, K., Yusri, I. M., Leman, A. M. and Yusaf, T.. 2017. "Response surface methodology (RSM) based multi-objective optimization of fusel oil-gasoline blends at different water content in SI engine." Energy Conversion and Management. 150, pp. 222-241. https://doi.org/10.1016/j.enconman.2017.07.047
A Comprehensive Review on Efficiency Enhancement of Solar Collectors Using Hybrid Nanofluids
Mahamude, Abu Shadate Faisal, Kamarulzaman, Muhamad Kamal, Harun, Wan Sharuzi Wan, Kadirgama, Kumaran, Ramasamy, Devarajan, Farhana, Kaniz, Bakar, Rosli Abu, Yusaf, Talal, Subramanion, Sivarao and Yousif, Belal. 2022. "A Comprehensive Review on Efficiency Enhancement of Solar Collectors Using Hybrid Nanofluids." Energies. 15 (4), pp. 1-25. https://doi.org/10.3390/en15041391
Hydrogen Energy Demand Growth Prediction and Assessment (2021–2050) Using a System Thinking and System Dynamics Approach
Yusaf, Talal, Laimon, Mohamd, Alrefae, Waleed, Kadirgama, Kumaran, Al Dhahad, Hayder, Ramasamy, Devarajan, Kamarulzaman, Mohd Kamal and Yousif, Belal. 2022. "Hydrogen Energy Demand Growth Prediction and Assessment (2021–2050) Using a System Thinking and System Dynamics Approach." Applied Sciences. 12 (2), pp. 1-16. https://doi.org/10.3390/app12020781
Experimental analysis on the performance, combustion/emission characteristics of a DI diesel engine using hydrogen in dual fuel mode
Bakar, R.A., Widudo, Kadirgama, K., Ramasamy, D., Yusaf, Talal, Kamarulzaman, M.K., Sivaraos, Aslfattahi, Navid, Samylingam, L. and Alwayzy, Sadam H.. 2022. "Experimental analysis on the performance, combustion/emission characteristics of a DI diesel engine using hydrogen in dual fuel mode." International Journal of Hydrogen Energy. 52 (Part C), pp. 843-860. https://doi.org/10.1016/j.ijhydene.2022.04.129
Experimental and numerical study to develop TRANSYS model for an active flat plate solar collector with an internally serpentine tube receiver
Al-Manea, Ahmed, Al-Rbaihat, Raed, Kadhim, Hakim T, Alahmer, Ali, Yusaf, Talal and Egab, Karim. 2022. "Experimental and numerical study to develop TRANSYS model for an active flat plate solar collector with an internally serpentine tube receiver." International Journal of Thermofluids. 15, pp. 1-9. https://doi.org/10.1016/j.ijft.2022.100189
Numerical analysis of hybrid nanofluid natural convection in a wavy walled porous enclosure: Local thermal non-equilibrium model
Kadhim, Hakim T., Al-Manea, Ahmed, Al-Shamani, Ali Najah and Yusaf, Talal. 2022. "Numerical analysis of hybrid nanofluid natural convection in a wavy walled porous enclosure: Local thermal non-equilibrium model." International Journal of Thermofluids. 15, pp. 1-10. https://doi.org/10.1016/j.ijft.2022.100190
Analysis of heat transfer and fluid flow in a microchannel heat sink with sidewall dimples and fillet profile
Okab, Abdullah K., Hasan, Hayder M., Hamzah, Mushtaq, Egab, Karim, Al-Manea, Ahmed and Yusaf, Talal. 2022. "Analysis of heat transfer and fluid flow in a microchannel heat sink with sidewall dimples and fillet profile." International Journal of Thermofluids. 15, pp. 1-8. https://doi.org/10.1016/j.ijft.2022.100192
Energy sector development: system dynamics analysis
Laimon, Mohamd, Mai, Thanh, Goh, Steven and Yusaf, Talal. 2019. "Energy sector development: system dynamics analysis." Applied Sciences. 10 (1), pp. 1-19. https://doi.org/10.3390/app10010134
The influence of emulsified water fuel containing fresh water microalgae on diesel engine performance, combustion, vibration and emission
Al-lwayzy, Saddam H., Yusaf, Talal, Saleh, Khalid and Yousif, Belal. 2019. "The influence of emulsified water fuel containing fresh water microalgae on diesel engine performance, combustion, vibration and emission." Energies. 12 (13), pp. 1-17. https://doi.org/10.3390/en12132546
Mixtures of n-butanol and iso-butanol blended with diesel: experimental investigation of combustion characteristics, engine performance and emission levels in a compression ignition engine
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P. and Yusaf, Talal. 2021. "Mixtures of n-butanol and iso-butanol blended with diesel: experimental investigation of combustion characteristics, engine performance and emission levels in a compression ignition engine." Biofuels. 12 (4), pp. 439-448. https://doi.org/10.1080/17597269.2018.1493565
Pulsed ultrasound as an energy saving mode for ultrasound treatment of surface water with terrestrial aquatic carbon
Al-juboori, Raed A., Yusaf, Talal and Bowtell, Les. 2018. "Pulsed ultrasound as an energy saving mode for ultrasound treatment of surface water with terrestrial aquatic carbon." Desalination and Water Treatment. 135, pp. 167-176. https://doi.org/10.5004/dwt.2018.23173
Butanol-acetone mixture blended with cottonseed biodiesel: spray characteristics evolution, combustion characteristics, engine performance and emission
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P., Yusaf, Talal and Al-lwayzy, Saddam. 2019. "Butanol-acetone mixture blended with cottonseed biodiesel: spray characteristics evolution, combustion characteristics, engine performance and emission." Proceedings of the Combustion Institute. 37 (4), pp. 4729-4739. https://doi.org/10.1016/j.proci.2018.08.035
Experimental investigation of hydrated butanol-acetone (BA) and diesel blend as alternative fuel for CI engines
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P. and Yusaf, Talal. 2018. "Experimental investigation of hydrated butanol-acetone (BA) and diesel blend as alternative fuel for CI engines." 37th International Symposium on Combustion. Dublin, Ireland 29 Jul - 03 Aug 2018 Pittsburgh, PA, United States.
Experimental and numerical investigation of spray characteristics of butanol-diesel blends
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P. and Yusaf, Talal. 2017. "Experimental and numerical investigation of spray characteristics of butanol-diesel blends." Masri, A. R., Cleary, M., Dunn, M., Kourmatzis, A., Hawkes, E., Kook, S. and Chan, Q. N. (ed.) 11th Asia-Pacific Conference on Combustion. Sydney, Australia 10 - 14 Dec 2017 Australia.
Experimental study of spray characteristics, engine performance and emission levels of acetone-butanol-ethanol mixture-diesel blends in a diesel engine
Algayyim, Sattar Jabbar Murad, Wandel, Andrew, Yusaf, Talal, Hamawand, Ihsan and Al-lwayzy, Saddam. 2017. "Experimental study of spray characteristics, engine performance and emission levels of acetone-butanol-ethanol mixture-diesel blends in a diesel engine." Masri, A. R., Cleary, M., Dunn, M., Kourmatzis, A., Hawkes, E., Kook, S. and Chan, Q. N. (ed.) 11th Asia-Pacific Conference on Combustion. Sydney, Australia 10 - 14 Dec 2017 Australia.
The effect of butanol-acetone mixture-cottonseed biodiesel blend on spray characteristics, engine performance and emissions in diesel engine
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P. and Yusaf, Talal. 2017. "The effect of butanol-acetone mixture-cottonseed biodiesel blend on spray characteristics, engine performance and emissions in diesel engine." Masri, A. R., Cleary, M., Dunn, M., Kourmatzis, A., Hawkes, E., Kook, S. and Chan, Q. N. (ed.) 11th Asia-Pacific Conference on Combustion. Sydney, Australia 10 - 14 Dec 2017 Australia.
Investigation of radial flow ejector performance through experiments and computational simulations
Rahimi, Hadi. 2017. Investigation of radial flow ejector performance through experiments and computational simulations. PhD Thesis Doctor of Philosophy. University of Southern Queensland. https://doi.org/10.26192/5c05de72d30d0
The impact of injector hole diameter on spray behaviour for butanol-diesel blends
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P. and Yusaf, Talal. 2018. "The impact of injector hole diameter on spray behaviour for butanol-diesel blends." Energies. 11 (5), pp. 1298-1310. https://doi.org/10.3390/en11051298
Impact of butanol-acetone mixture as a fuel additive on diesel engine performance and emissions
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P., Yusaf, Talal, Al-Lwayzy, Saddam and Hamawand, Ihsan. 2018. "Impact of butanol-acetone mixture as a fuel additive on diesel engine performance and emissions." Fuel: the science and technology of fuel and energy. 227, pp. 118-126. https://doi.org/10.1016/j.fuel.2018.04.091
Production and application of ABE as a biofuel
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P., Yusaf, Talal and Hamawand, Ihsan. 2018. "Production and application of ABE as a biofuel." Renewable and Sustainable Energy Reviews. 82, pp. 1195-1214. https://doi.org/10.1016/j.rser.2017.09.082
A critical review on processes and energy profile of the Australian meat processing industry
Hamawand, Ihsan, Ghadouani, Anas, Bundschuh, Jochen, Hamawand, Sara, Al Juboori, Raed A., Chakrabarty, Sayan and Yusaf, Talal. 2017. "A critical review on processes and energy profile of the Australian meat processing industry." Energies. 10 (5). https://doi.org/10.3390/en10050731
The impact of n-butanol and iso-butanol as components of butanol-acetone (BA) mixture-diesel blend on spray, combustion characteristics, engine performance and emission in direct injection diesel engine
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P., Yusaf, Talal and Hamawand, Ihsan. 2017. "The impact of n-butanol and iso-butanol as components of butanol-acetone (BA) mixture-diesel blend on spray, combustion characteristics, engine performance and emission in direct injection diesel engine." Energy. 140, pp. 1074-1086. https://doi.org/10.1016/j.energy.2017.09.044
Investigation of ethanol production potential from lignocellulosic material without enzymatic hydrolysis using the ultrasound technique
Kandasamy, Manoj, Hamawand, Ihsan, Bowtell, Leslie, Seneweera, Saman, Chakrabarty, Sayan, Yusaf, Talal, Shakoor, Zaidoon, Algayyim, Sattar and Eberhard, Friederike. 2017. "Investigation of ethanol production potential from lignocellulosic material without enzymatic hydrolysis using the ultrasound technique." Energies. 10 (1), pp. 62-73. https://doi.org/10.3390/en10010062
Algae-biomass for fuel, electricity and agriculture
Bundschuh, Jochen, Yusaf, Talal, Maity, Jyoti Prakash, Nelson, Emily, Mamat, Rizalman and Mahlia, T. M. Indra. 2014. "Algae-biomass for fuel, electricity and agriculture ." Energy. 78, pp. 1-3. https://doi.org/10.1016/j.energy.2014.11.005
Influence of chemical blends on palm oil methyl esters' cold flow properties and fuel characteristics
Ali, Obed M., Yusaf, Talal, Mamat, Rizalman, Abdullah, Nik R. and Abdullah, Abdul Adam. 2014. "Influence of chemical blends on palm oil methyl esters' cold flow properties and fuel characteristics." Energies. 7 (7), pp. 4364-4380. https://doi.org/10.3390/en7074364
Sustainable energy and climate protection solutions in agriculture
Bundschuh, Jochen, Chen, Guangnan, Yusaf, Talal, Yan, Jinyue and Chen, Shulin. 2014. "Sustainable energy and climate protection solutions in agriculture ." Applied Energy. 114, pp. 735-736. https://doi.org/10.1016/j.apenergy.2013.11.037
Optimization of biodiesel-diesel blended fuel properties and engine performance with ether additive using statistical analysis and response surface methods
Ali, Obed M., Mamat, Rizalman, Najafi, Gholamhassan, Yusaf, Talal and Ardebili, Seyed Mohammad Safieddin. 2015. "Optimization of biodiesel-diesel blended fuel properties and engine performance with ether additive using statistical analysis and response surface methods." Energies. 8 (12), pp. 14136-14150. https://doi.org/10.3390/en81212420
TOPSIS multi-criteria decision modeling approach for biolubricant selection for two-stroke petrol engines
Soufi, Masoud Dehghani, Ghobadian, Barat, Najafi, Gholamhassan, Sabzimaleki, Mohammad Reza and Yusaf, Talal. 2015. "TOPSIS multi-criteria decision modeling approach for biolubricant selection for two-stroke petrol engines." Energies. 8 (12), pp. 13960-13970. https://doi.org/10.3390/en81212408
Combustion of microalgae oil and ethanol blended with diesel fuel
Al-lwayzy, Saddam H. and Yusaf, Talal. 2015. "Combustion of microalgae oil and ethanol blended with diesel fuel." Energies. 8 (12), pp. 13985-13995. https://doi.org/10.3390/en81212409
Glycerin, a biodiesel by-product with potentiality to produce hydrogen by steam gasification
Suero, Silvia Roman, Cano, Beatriz Ledesma, Alvarez-Murillo, Andres, Al-Kassir, Awf and Yusaf, Talal. 2015. "Glycerin, a biodiesel by-product with potentiality to produce hydrogen by steam gasification." Energies. 8 (11), pp. 12765-12775. https://doi.org/10.3390/en81112339
SVM and ANFIS for prediction of performance and exhaust emissions of a SI engine with gasoline-ethanol blended fuels
Najafi, G., Ghobadian, B., Moosavian, A., Yusaf, T., Mamat, R., Kettner, M. and Azmi, W. H.. 2016. "SVM and ANFIS for prediction of performance and exhaust emissions of a SI engine with gasoline-ethanol blended fuels." Applied Thermal Engineering. 95, pp. 186-203. https://doi.org/10.1016/j.applthermaleng.2015.11.009
Synthesis and optimization of Hevea brasiliensis and Ricinus communis as feedstock for biodiesel production: a comparative study
Silitonga, A. S., Masjuki, H. H., Ong, Hwai Chyuan, Kusumo, F., Yusaf, Talal and Mahlia, T. M. I.. 2016. "Synthesis and optimization of Hevea brasiliensis and Ricinus communis as feedstock for biodiesel production: a comparative study." Industrial Crops and Products. 85, pp. 274-286. https://doi.org/10.1016/j.indcrop.2016.03.017
Impact of butanol-acetone mixture as an oxygenated fuel additive to diesel fuel on diesel engine performance and emissions
Algayyim, Sattar, Wandel, Andrew, Yusaf, Talal, Hamawand, Ihsan and Al-lwayzy, Saddam. 2016. "Impact of butanol-acetone mixture as an oxygenated fuel additive to diesel fuel on diesel engine performance and emissions." 36th International Symposium on Combustion. Seoul, Korea 31 Jul - 05 Aug 2016
The experimental investigation of butanol-diesel blend on engine performance and emission levels in DI diesel engine
Algayyim, Sattar, Wandel, Andrew P., Yusaf, Talal, Hamawand, Ihsan and Al-lwayzy, Saddam. 2017. "The experimental investigation of butanol-diesel blend on engine performance and emission levels in DI diesel engine." 1st MoHESR and HCED Iraq Scholars Conference in Australasia 2017 (ISCA 2017). Melbourne, Australia 05 - 06 Dec 2017 Melbourne, Australia.
Design, fabrication and evaluation of gamma-type stirling engine to produce electricity from biomass for the micro-CHP system
Damirchi, Hojjat, Najafi, Gholam Hassan, Alizadehnia, Siamak, Ghobadian, Barat, Yusaf, Talal and Mamat, Rizalman. 2015. "Design, fabrication and evaluation of gamma-type stirling engine to produce electricity from biomass for the micro-CHP system." The 7th International Conference on Applied Energy - ICAE2015. Abu Dhabi, United Arab Emirates 28 - 31 Mar 2015 Netherlands. https://doi.org/10.1016/j.egypro.2015.07.240
Energy conversion efficiency of pulsed ultrasound
Al-Juboori, Raed A., Yusaf, Talal and Bowtell, Leslie. 2015. "Energy conversion efficiency of pulsed ultrasound." The 7th International Conference on Applied Energy - ICAE2015. Abu Dhabi, United Arab Emirates 28 - 31 Mar 2015 Netherlands. Elsevier. https://doi.org/10.1016/j.egypro.2015.07.340
The study of air fuel ratio for open furnace MILD combustion of biogas on bluff-body burner
Noor, M. M., Wandel, Andrew P. and Yusaf, T. F.. 2012. "The study of air fuel ratio for open furnace MILD combustion of biogas on bluff-body burner." 2012 Southern Regional Engineering Conference (SREC 2012). Toowoomba, Australia 01 Sep 2012 Canberra, Australia.
Biofuel from microalgae: alternative, sustainable and renewable fuel
Najafi, Gholamhassan, Ghobadian, Barat and Yusaf, Talal F.. 2011. "Biofuel from microalgae: alternative, sustainable and renewable fuel ." 10th International Conference on Sustainable Energy Technologies (SET 2011). Istanbul, Turkey 04 - 07 Sep 2011
Evaluation of alternative energy sources for cotton production in Australia
Chen, Guangnan, Sandell, Gary, Yusaf, Talal and Baillie, Craig. 2013. "Evaluation of alternative energy sources for cotton production in Australia." SEAg 2013: Innovative Agricultural Technologies for a Sustainable Future. Barton, Australia 22 - 25 Sep 2013 Barton, ACT, Australia.
Corrosion effects of CNT-nanofluids on different metals
Ismail, A. F., Anuar, A., Rashmi, W. and Yusaf, T.. 2014. "Corrosion effects of CNT-nanofluids on different metals." 3rd International Conference on Advanced Materials and Information Technology Processing (AMITP 2013). Los Angeles, United States 01 - 02 Dec 2013 Southampton, United Kingdom. https://doi.org/10.2495/AMITP20130171
Wear and frictional behaviour of metals
Alotaibi, J. G., Yousif, B. F. and Yusaf, T. F.. 2014. "Wear and frictional behaviour of metals." Kida, Katsuyuki (ed.) 3rd International Conference on Advanced Materials and Engineering Materials (ICAMEM 2013). Singapore 14 - 15 Dec 2013 Zurich, Switzerland. https://doi.org/10.4028/www.scientific.net/AMR.893.430
The development of MILD combustion open burner experimental setup
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "The development of MILD combustion open burner experimental setup." Ishak, Mahadzir and Rahman, Md. Mustafizur (ed.) 2nd International Conference of Mechanical Engineering Research (ICMER 2013). Pahang, Malaysia 01 - 03 Jul 2013 Pahang, Malaysia.
Detail guide for CFD on the simulation of biogas combustion in bluff-body mild burner
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "Detail guide for CFD on the simulation of biogas combustion in bluff-body mild burner." Ishak, Mahadzir and Rahman, Md. Mustafizur (ed.) 2nd International Conference of Mechanical Engineering Research (ICMER 2013). Pahang, Malaysia 01 - 03 Jul 2013 Pahang, Malaysia.
Mild combustion: the future for lean and clean combustion
Yusaf, Talal, Noor, M. M. and Wandel, Andrew P.. 2013. "Mild combustion: the future for lean and clean combustion." Ishak, Mahadzir and Rahman, Md. Mustafizur (ed.) 2nd International Conference of Mechanical Engineering Research (ICMER 2013). Pahang, Malaysia 01 - 03 Jul 2013 Pahang, Malaysia.
Alternative energy sources fro cotton production
Baillie, Craig, Sandell, Gary, Chen, Guangnan and Yusaf, Talal. 2012. "Alternative energy sources fro cotton production." 16th Australian Cotton Conference (ACC 2012): Growing Better all the Time. Gold Coast, Australia 14 - 16 Aug 2012 Gold Coast, Australia.
Investigation of the effect of additives to natural gas on heavy-duty SI engine combustion characteristics
Gharehghani, A., Hosseini, R. and Yusaf, T.. 2013. "Investigation of the effect of additives to natural gas on heavy-duty SI engine combustion characteristics." Journal of Mechanical Engineering and Sciences. 5, pp. 677-687. https://doi.org/10.15282/jmes.5.2013.14.0065
Characterization of a diesel engine operating with a small proportion of methanol as a fuel additive in biodiesel blend
Mat Yasin, M. H., Yusaf, Talal, Mamat, R. and Yusop, A. Fitri. 2014. "Characterization of a diesel engine operating with a small proportion of methanol as a fuel additive in biodiesel blend." Applied Energy. 114, pp. 865-873. https://doi.org/10.1016/j.apenergy.2013.06.012
Transesterification of Nannochloropsis oculata microalga's oil to biodiesel using calcium methoxide catalyst
Teo, Siow Hwa, Islam, Aminul, Yusaf, Talal and Taufiq-Yap, Yun Hin. 2014. "Transesterification of Nannochloropsis oculata microalga's oil to biodiesel using calcium methoxide catalyst." Energy. 78, pp. 63-71. https://doi.org/10.1016/j.energy.2014.07.045
Numerical and experimental study of microorganism disruption using shock treatment
Yusaf, Talal and Al Juboori, Raed A.. 2015. "Numerical and experimental study of microorganism disruption using shock treatment." Journal of Biotechnology. 208 (Supplement), pp. S15-S15. https://doi.org/10.1016/j.jbiotec.2015.06.035
Investigating natural organic carbon removal and structural alteration induced by pulsed ultrasound
Al-Juboori, Raed A., Yusaf, Talal, Aravinthan, Vasantha and Bowtell, Leslie. 2016. "Investigating natural organic carbon removal and structural alteration induced by pulsed ultrasound." Science of the Total Environment. 541, pp. 1019-1030. https://doi.org/10.1016/j.scitotenv.2015.09.143
Insights into the scalability of magnetostrictive ultrasound technology for water treatment applications
Al-Juboori, Raed A., Bowtell, Leslie A., Yusaf, Talal and Aravinthan, Vasantha. 2016. "Insights into the scalability of magnetostrictive ultrasound technology for water treatment applications." Ultrasonics Sonochemistry. 28, pp. 357-366. https://doi.org/10.1016/j.ultsonch.2015.08.013
Determination of drying characteristics of biomass residues to be used as a renewable fuel
Al Kassir, Awf, Yusaf, Talal, Al Karany, Raul Kassir and Hamawand, Ihsan. 2015. "Determination of drying characteristics of biomass residues to be used as a renewable fuel." Journal of Biotechnology. 208 (Supplement), pp. S15-S15. https://doi.org/10.1016/j.jbiotec.2015.06.034
Single-zone zero-dimensional model study for diesel-fuelled homogeneous charge compression ignition (HCCI) engines using Cantera
Hairuddin, A. Aziz, Yusaf, Talal and Wandel, Andrew P.. 2016. "Single-zone zero-dimensional model study for diesel-fuelled homogeneous charge compression ignition (HCCI) engines using Cantera." International Journal of Automotive and Mechanical Engineering. 13 (2), pp. 3309-3328. https://doi.org/10.15282/ijame.13.2.2016.3.0275
Diesel engine performance and exhaust gas emissions using microalgae Chlorella protothecoides biodiesel
Al-lwayzy, Saddam H. and Yusaf, Talal. 2017. "Diesel engine performance and exhaust gas emissions using microalgae Chlorella protothecoides biodiesel." Renewable Energy. 101, pp. 690-701. https://doi.org/10.1016/j.renene.2016.09.035
Bioenergy from cotton industry wastes: a review and potential
Hamawand, Ihsan, Sandell, Gary, Pittaway, Pam, Chakrabarty, Sayan, Yusaf, Talal, Chen, Guangnan, Seneweera, Saman, Al-Lwayzy, Saddam, Bennett, John and Hopf, Joshua. 2016. "Bioenergy from cotton industry wastes: a review and potential." Renewable and Sustainable Energy Reviews. 66, pp. 435-448. https://doi.org/10.1016/j.rser.2016.08.033
An assessment of direct on-farm energy use for high value grain crops grown under different farming practices in Australia
Maraseni, Tek, Chen, Guangnan, Banhazi, Thomas, Bundschuh, Jochen and Yusaf, Talal. 2015. "An assessment of direct on-farm energy use for high value grain crops grown under different farming practices in Australia." Energies. 8 (11), pp. 13033-13046. https://doi.org/10.3390/en81112353
Tracking ultrasonically structural changes of natural aquatic organic carbon: chemical fractionation and spectroscopic approaches
Al-Juboori, Raed A., Yusaf, Talal, Aravinthan, Vasantha and Bowtell, Leslie. 2016. "Tracking ultrasonically structural changes of natural aquatic organic carbon: chemical fractionation and spectroscopic approaches." Chemosphere. 145, pp. 231-248. https://doi.org/10.1016/j.chemosphere.2015.11.079
Optimization of performance and exhaust emission parameters of a SI (spark ignition) engine with gasoline-ethanol blended fuels using response surface methodology
Najafi, Gholamhassan, Ghobadian, Barat, Yusaf, Talal, Ardebili, Seyed Mohammad Safieddin and Mamat, Rizalman. 2015. "Optimization of performance and exhaust emission parameters of a SI (spark ignition) engine with gasoline-ethanol blended fuels using response surface methodology." Energy. 90 (2), pp. 1815-1829. https://doi.org/10.1016/j.energy.2015.07.004
Solar energy in Iran: current state and outlook
Najafi, G., Ghobadian, B., Mamat, R., Yusaf, T. and Azmi, W. H.. 2015. "Solar energy in Iran: current state and outlook." Renewable and Sustainable Energy Reviews. 49, pp. 931-942. https://doi.org/10.1016/j.rser.2015.04.056
An experimental study on reactivity controlled compression ignition engine fueled with biodiesel/natural gas
Gharehghani, Ayatallah, Hosseini, Reza, Mirsalim, Mostafa, Jazayeri, S. Ali and Yusaf, Talal. 2015. "An experimental study on reactivity controlled compression ignition engine fueled with biodiesel/natural gas." Energy. 89, pp. 558-567. https://doi.org/10.1016/j.energy.2015.06.014
A comparative study on the first and second law analysis and performance characteristics of a spark ignition engine using either natural gas or gasoline
Gharehghani, A., Hosseini, R., Mirsalim, M. and Yusaf, Talal F.. 2015. "A comparative study on the first and second law analysis and performance characteristics of a spark ignition engine using either natural gas or gasoline." Fuel: the science and technology of fuel and energy. 158, pp. 488-493. https://doi.org/10.1016/j.fuel.2015.05.067
Exploring the correlations between common UV measurements and chemical fractionation for natural waters
Al-Juboori, Raed A., Yusaf, Talal and Pittaway, Pamela A.. 2016. "Exploring the correlations between common UV measurements and chemical fractionation for natural waters ." Desalination and Water Treatment. 57 (35), pp. 16324-16335. https://doi.org/10.1080/19443994.2015.1079805
A computational study of operating range extension in a natural gas SI engine with the use of hydrogen
Gharehghani, A., Hosseini, R., Mirsalim, M. and Yusaf, Talal F.. 2015. "A computational study of operating range extension in a natural gas SI engine with the use of hydrogen." International Journal of Hydrogen Energy. 40 (17), pp. 5966-5975. https://doi.org/10.1016/j.ijhydene.2015.03.015
A comparison of household carbon emission patterns of urban and rural China over the 17 year period (1995–2011)
Qu, Jiansheng, Maraseni, Tek, Liu, Lina, Zhang, Zhiqiang and Yusaf, Talal. 2015. "A comparison of household carbon emission patterns of urban and rural China over the 17 year period (1995–2011)." Energies. 8 (9), pp. 10537-10557. https://doi.org/10.3390/en80910537
Impact of pulsed ultrasound on bacteria reduction of natural waters
Al-Juboori, Raed A., Aravinthan, Vasantha and Yusaf, Talal. 2015. "Impact of pulsed ultrasound on bacteria reduction of natural waters." Ultrasonics Sonochemistry. 27, pp. 137-147. https://doi.org/10.1016/j.ultsonch.2015.05.007
The influence of straight vegetable oil fatty acid composition on compression ignition combustion and emissions
Hellier, Paul, Ladommatos, Nicos and Yusaf, Talal. 2015. "The influence of straight vegetable oil fatty acid composition on compression ignition combustion and emissions." Fuel: the science and technology of fuel and energy. 143, pp. 131-143. https://doi.org/10.1016/j.fuel.2014.11.021
Assessing the application and downstream effects of pulsed mode ultrasound as a pre-treatment for alum coagulation
Al-Juboori, Raed A., Aravinthan, Vasantha, Yusaf, Talal and Bowtell, Leslie. 2016. "Assessing the application and downstream effects of pulsed mode ultrasound as a pre-treatment for alum coagulation." Ultrasonics Sonochemistry. 31, pp. 7-19. https://doi.org/10.1016/j.ultsonch.2015.11.028
Evaluating the impact of operating parameters on biocidal effects of pulsed ultrasound in natural water disinfection
Al Juboori, Raed A., Yusaf, Talal and Aravinthan, Vasantha. 2015. "Evaluating the impact of operating parameters on biocidal effects of pulsed ultrasound in natural water disinfection." Journal of Biotechnology. 208 (Supplement), pp. S17-S18. https://doi.org/10.1016/j.jbiotec.2015.06.042
Brass, aluminium, and mild steel sliding against stainless steel under dry conditions
Alotaibi, J. G., Yousif, B. F. and Yusaf, T. F.. 2015. "Brass, aluminium, and mild steel sliding against stainless steel under dry conditions." International Journal of Precision Technology. 5 (2), pp. 85-96.
Wear behaviour and mechanism of different metals sliding against stainless steel counterface
Alotaibi, J. G., Yousif, B. F. and Yusaf, T. F.. 2014. "Wear behaviour and mechanism of different metals sliding against stainless steel counterface." Proceedings of the Institution of Mechanical Engineers Part J: Journal of Engineering Tribology. 228 (6), pp. 692-704. https://doi.org/10.1177/1350650114527072
Evaluating the effect of heat transfer on cell disruption in ultrasound processes
Yusaf, Talal. 2015. "Evaluating the effect of heat transfer on cell disruption in ultrasound processes." Annals of Microbiology. 65 (3), pp. 1447-1456. https://doi.org/10.1007/s13213-014-0983-z
Engine performance and emissions using Jatropha curcas, Ceiba pentandra and Calophyllum inophyllum biodiesel in a CI diesel engine
Ong, Hwai Chyuan, Masjuki, H. H., Mahlia, T. M. I., Silitonga, A. S., Chong, W. T. and Yusaf, Talal. 2014. "Engine performance and emissions using Jatropha curcas, Ceiba pentandra and Calophyllum inophyllum biodiesel in a CI diesel engine." Energy. 69, pp. 427-445. https://doi.org/10.1016/j.energy.2014.03.035
Growing algae using water from coal seam gas industry and harvesting using an innovative technique: a review and a potential
Hamawand, Ihsan, Yusaf, Talal and Hamawand, Sara. 2014. "Growing algae using water from coal seam gas industry and harvesting using an innovative technique: a review and a potential." Fuel: the science and technology of fuel and energy. 117 (Part A), pp. 422-430. https://doi.org/10.1016/j.fuel.2013.09.040
An introduction to a homogeneous charge compression ignition engine
Hairuddin, A. A., Wandel, A. P. and Yusaf, T.. 2014. "An introduction to a homogeneous charge compression ignition engine." Journal of Mechanical Engineering and Sciences. 7, pp. 1042-1052. https://doi.org/10.15282/jmes.7.2014.3.0101
Investigating the feasibility and the optimal location of pulsed ultrasound in surface water treatment schemes
Al-Juboori, Raed A., Yusaf, Talal, Aravinthan, Vasantha, Pittaway, Pamela A. and Bowtell, Leslie. 2016. "Investigating the feasibility and the optimal location of pulsed ultrasound in surface water treatment schemes." Desalination and Water Treatment. 57 (11), pp. 4769-4787. https://doi.org/10.1080/19443994.2014.996771
Investigating corrosion effects and heat transfer enhancement in smaller size radiators using CNT-nanofluids
Rashmi, W., Ismail, A. F., Khalid, M., Anuar, A. and Yusaf, T.. 2014. "Investigating corrosion effects and heat transfer enhancement in smaller size radiators using CNT-nanofluids." Journal of Materials Science. 49 (13), pp. 4544-4551. https://doi.org/10.1007/s10853-014-8154-y
Statistical diagnosis of the best weibull methods for wind power assessment for agricultural applications
Azad, Abul Kalam, Rasul, Mohammad Golam and Yusaf, Talal. 2014. "Statistical diagnosis of the best weibull methods for wind power assessment for agricultural applications." Energies. 7 (5), pp. 3056-3085. https://doi.org/10.3390/en7053056
A review of hydrogen and natural gas addition in diesel HCCI engines
Hairuddin, A. Aziz, Yusaf, Talal and Wandel, Andrew P.. 2014. "A review of hydrogen and natural gas addition in diesel HCCI engines." Renewable and Sustainable Energy Reviews. 32, pp. 739-761. https://doi.org/10.1016/j.rser.2014.01.018
Energy characterisation of ultrasonic systems for industrial processes
Al-Juboori, Raed A., Yusaf, Talal, Bowtell, Leslie and Aravinthan, Vasantha. 2015. "Energy characterisation of ultrasonic systems for industrial processes." Ultrasonics. 57, pp. 18-30. https://doi.org/10.1016/j.ultras.2014.10.003
Coals seam gas (CSG) in agriculture - a review: technical and market analysis for Australia
Yusaf, Talal, Hamawand, Ihsan, Schmidt, Erik, Binnie, James, Rees, Steven and Chakrabarty, Sayan. 2014. "Coals seam gas (CSG) in agriculture - a review: technical and market analysis for Australia ." Sustainable Energy Technologies and Assessments. 8, pp. 149-158. https://doi.org/10.1016/j.seta.2014.08.005
New technique measuring film thickness for tribological machines
Al-Haddad, A. A., Salih, Nbhan D., Wen, Chin Chee, Yusaf, T. F. and Yousif, B. F.. 2010. "New technique measuring film thickness for tribological machines." 2009 ASME International Mechanical Engineering Congress and Exposition (IMECE 2009). Florida, United States of America 13 - 19 Nov 2009 United States. https://doi.org/10.1115/IMECE2009-10160
Air fuel ratio study for mixture of biogas and hydrogen on mild combustion
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2014. "Air fuel ratio study for mixture of biogas and hydrogen on mild combustion." International Journal of Automotive and Mechanical Engineering. 10 (1), pp. 2144-2154. https://doi.org/10.15282/ijame.9.2013.29.0180
Effect of air-fuel ratio on temperature distribution and pollutants for biogas MILD combustion
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2014. "Effect of air-fuel ratio on temperature distribution and pollutants for biogas MILD combustion." International Journal of Automotive and Mechanical Engineering. 10 (1), pp. 1980-1992. https://doi.org/10.15282/ijame.10.2014.15.0166
The simulation of biogas combustion in a MILD burner
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2014. "The simulation of biogas combustion in a MILD burner." Journal of Mechanical Engineering and Sciences. 6 (1), pp. 995-1013.
Design of film thickness instrument for fibre polymer composites tribological experiments
Yousif, B. F., Al-Haddad, A., Alotaibi, J. GH. and Yusaf, T. F.. 2014. "Design of film thickness instrument for fibre polymer composites tribological experiments." Journal of Engineering Science and Technology. 9 (2), pp. 154-166.
An experimental investigation of the effective parameters on wet washing of biodiesel purification
Abbaszadeh, A., Ghobadian, B., Najafi, G. and Yusaf, T.. 2014. "An experimental investigation of the effective parameters on wet washing of biodiesel purification." International Journal of Automotive and Mechanical Engineering. 9 (1), pp. 1525-1537. https://doi.org/10.15282/ijame.9.2013.4.0126
Smaller radiator with enhanced heat transfer using CNT-nanofluids
Ismail, A. F., Abd-Halim, B. A., Rashmi, W. and Yusaf, T.. 2014. "Smaller radiator with enhanced heat transfer using CNT-nanofluids ." Yang, G. (ed.) International Conference on Future Energy, Environment, and Materials (FEEM 2013). Hong Kong, China 24 - 25 Dec 2013 Southampton, United Kingdom. https://doi.org/10.2495/FEEM20130221
Chlorella protothecoides microalgae as an alternative fuel for tractor diesel engines
Al-lwayzy, Saddam H. and Yusaf, Talal. 2013. "Chlorella protothecoides microalgae as an alternative fuel for tractor diesel engines." Energies. 6 (2), pp. 766-783. https://doi.org/10.3390/en6020766
Coal seam gas and associated water: a review paper
Hamawand, Ihsan, Yusaf, Talal and Hamawand, Sara. 2013. "Coal seam gas and associated water: a review paper." Renewable and Sustainable Energy Reviews. 22, pp. 550-560. https://doi.org/10.1016/j.rser.2013.02.030
Study and modelling drying of banana slices under superheated steam
Hamawand, Ihsan, Yusaf, Talal and Bennett, John. 2014. "Study and modelling drying of banana slices under superheated steam." Asia Pacific Journal of Chemical Engineering. 9 (4), pp. 591-603. https://doi.org/10.1002/apj.1788
Biofuels from the fresh water microalgae Chlorella vulgaris (FWM-CV) for diesel engines
Al-lwayzy, Saddam H., Yusaf, Talal and Al-Juboori, Raed A.. 2014. "Biofuels from the fresh water microalgae Chlorella vulgaris (FWM-CV) for diesel engines." Energies. 7 (3), pp. 1829-1851. https://doi.org/10.3390/en7031829
Assessing a new approach to covered anaerobic pond design in the treatment of abattoir wastewater
McCabe, B. K., Harris, P., Baillie, C., Pittaway, P. and Yusaf, T.. 2013. "Assessing a new approach to covered anaerobic pond design in the treatment of abattoir wastewater." Australian Journal of Multi-Disciplinary Engineering. 10 (1), pp. 81-93. https://doi.org/10.7158/N12-AE07.2013.10.1.
MILD combustion: the future for lean and clean combustion technology
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2014. "MILD combustion: the future for lean and clean combustion technology." International Review of Mechanical Engineering. 8 (1), pp. 251-257.
Design and development of mild combustion burner
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "Design and development of mild combustion burner." Journal of Mechanical Engineering and Sciences. 5, pp. 662-676. https://doi.org/10.15282/jmes.5.2013.13.0064
Effect of different heat transfer models on a diesel homogeneous charge compression ignition engine
Hairuddin, Abdul Aziz, Yusaf, Talal and Wandel, Andrew. 2013. "Effect of different heat transfer models on a diesel homogeneous charge compression ignition engine." International Journal of Automotive and Mechanical Engineering. 8 (1), pp. 1292-1304.
Implementation of CMC in a 0-D single-zone model of a diesel HCCI engine
Hairuddin, A. Aziz, Yusaf, Talal and Wandel, Andrew P.. 2013. "Implementation of CMC in a 0-D single-zone model of a diesel HCCI engine." Zhu, Mingming, Yu, Yun, Vuthaluru, Hari, Zhang, Zhezi and Zhang, Dongke (ed.) 7th Australian Combustion Symposium (ACS 2013). Perth, Australia 06 - 08 Nov 2013 Sydney, Australia.
Experimental study of microorganism disruption using shear stress
Yusaf, Talal. 2013. "Experimental study of microorganism disruption using shear stress." Biochemical Engineering Journal. 79, pp. 7-14. https://doi.org/10.1016/j.bej.2013.07.001
The effect of methanol-diesel blended ratio on CI engine performance
Yusaf, T., Hamawand, I., Baker, P. and Najafi, G.. 2013. "The effect of methanol-diesel blended ratio on CI engine performance." International Journal of Automotive and Mechanical Engineering. 8 (1), pp. 1385-1395. https://doi.org/10.15282/ijame.8.2013.26.0114
Effect of compressed natural gas mixing on the engine performance and emissions
Yusaf, T., Baker, P., Hamawand, I. and Noor, M. M.. 2013. "Effect of compressed natural gas mixing on the engine performance and emissions." International Journal of Automotive and Mechanical Engineering. 8 (1), pp. 1416-1429.
Analysis of recirculation zone and ignition position of non-premixed bluff-body for biogas mild combustion
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "Analysis of recirculation zone and ignition position of non-premixed bluff-body for biogas mild combustion." International Journal of Automotive and Mechanical Engineering. 8 (1), pp. 1176-1186.
The analysis of recirculation zone and ignition position of non-premixed bluff-body for biogas mild combustion
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "The analysis of recirculation zone and ignition position of non-premixed bluff-body for biogas mild combustion." Ishak, Mahadzir and Rahman, Md. Mustafizur (ed.) 2nd International Conference of Mechanical Engineering Research (ICMER 2013). Pahang, Malaysia 01 - 03 Jul 2013 Pahang, Malaysia.
Particles motion in a cascading rotary drum dryer
Hamawand, Ihsan and Yusaf, Talal. 2014. "Particles motion in a cascading rotary drum dryer." Canadian Journal of Chemical Engineering. 92 (4), pp. 648-662. https://doi.org/10.1002/cjce.21845
Experimental investigation of thermal balance of a turbocharged SI engine operating on natural gas
Gharehghani, A., Koochak, M., Mirsalim, M. and Yusaf, Talal. 2013. "Experimental investigation of thermal balance of a turbocharged SI engine operating on natural gas." Applied Thermal Engineering. 60 (1-2), pp. 200-207. https://doi.org/10.1016/j.applthermaleng.2013.06.029
Experimental investigation of the tractor engine performance using diesohol fuel
Shadidi, Behdad, Yusaf, Talal, Alizadeh, Hossein Haji Agha and Ghobadian, Barat. 2014. "Experimental investigation of the tractor engine performance using diesohol fuel." Applied Energy. 114, pp. 874-879. https://doi.org/10.1016/j.apenergy.2013.06.011
Nutrient removal of nursery and municipal wastewater using Chlorella vulgaris microalgae for lipid extraction
Aravinthan, Vasantha, Story, Nadine and Yusaf, Talal. 2014. "Nutrient removal of nursery and municipal wastewater using Chlorella vulgaris microalgae for lipid extraction." Desalination and Water Treatment. 52 (4-6), pp. 727-736. https://doi.org/10.1080/19443994.2013.826325
Recycling of waste engine oils using a new washing agent
Hamawand, Ihsan, Yusaf, Talal and Rafat, Sardasht. 2013. "Recycling of waste engine oils using a new washing agent." Energies. 6 (2), pp. 1023-1049. https://doi.org/10.3390/en6021023
Production of biodiesel from Sterculia foetida and its process optimization
Silitonga, A. S., Ong, H. C., Masjuki, H. H., Mahlia, T. M. I., Chong, W. T. and Yusaf, Talal F.. 2013. "Production of biodiesel from Sterculia foetida and its process optimization ." Fuel: the science and technology of fuel and energy. 111, pp. 478-484. https://doi.org/10.1016/j.fuel.2013.03.051
Numerical study of oxygen dilution and temperature distribution of biogas combustion in Bluff-body MILD burner
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "Numerical study of oxygen dilution and temperature distribution of biogas combustion in Bluff-body MILD burner." Masri, Assaad (ed.) 7th Australian Combustion Symposium (ACS 2013). Perth, Australia 06 - 08 Nov 2013 Perth, Australia.
A case study for biogas generation from covered anaerobic ponds treating abattoir wastewater: investigation of pond performance and potential biogas production
McCabe, Bernadette K., Hamawand, Ihsan, Harris, Peter, Baillie, Craig and Yusaf, Talal. 2014. "A case study for biogas generation from covered anaerobic ponds treating abattoir wastewater: investigation of pond performance and potential biogas production." Applied Energy. 114, pp. 798-808. https://doi.org/10.1016/j.apenergy.2013.10.020
Alternative methods of microorganism disruption for agricultural applications
Yusaf, Talal and Al-Juboori, Raed A.. 2014. "Alternative methods of microorganism disruption for agricultural applications ." Applied Energy. 114, pp. 909-923. https://doi.org/10.1016/j.apenergy.2013.08.085
The air fuel ratio study for the mixture of biogas and hydrogen on mild combustion
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "The air fuel ratio study for the mixture of biogas and hydrogen on mild combustion." 3rd Malaysian Postgraduate Conference (MPC 2013). Sydney, Australia 04 - 05 Jul 2013 Sydney, Australia.
Discretization of three dimensional non-uniform grid: conditional moment closure elliptic equation using finite difference method
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "Discretization of three dimensional non-uniform grid: conditional moment closure elliptic equation using finite difference method." 3rd Malaysian Postgraduate Conference (MPC 2013). Sydney, Australia 04 - 05 Jul 2013 Sydney, Australia.
A homogeneous charge compression ignition engine: an introduction
Hairuddin, A. Aziz, Wandel, Andrew P. and Yusaf, Talal. 2013. "A homogeneous charge compression ignition engine: an introduction." 3rd Malaysian Postgraduate Conference (MPC 2013). Sydney, Australia 04 - 05 Jul 2013 Sydney, Australia.
Investigating the efficiency of ultrasound for controlling bio-fouling in batch membrane systems
Yusaf, T. F. and Al-Juboori, Raed Ahmed. 2012. "Investigating the efficiency of ultrasound for controlling bio-fouling in batch membrane systems ." Noor, M. M., Baker, Paul and Yusaf, Talal F. (ed.) USQ Combustion Meeting 2012 (21st November). Toowoomba, Australia 21 Nov 2012 Toowoomba, Australia.
The use of microalgae biodiesel in diesel engine: production, extraction and engine performance
Yusaf, T. F. and Al-lwayzy, Saddam H.. 2012. "The use of microalgae biodiesel in diesel engine: production, extraction and engine performance." Noor, M. M., Baker, Paul and Yusaf, Talal F. (ed.) USQ Combustion Meeting 2012 (21st November). Toowoomba, Australia 21 Nov 2012 Toowoomba, Australia.
A review of mild combustion and open furnace design consideration
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2012. "A review of mild combustion and open furnace design consideration." International Journal of Automotive and Mechanical Engineering. 6 (1), pp. 730-754.
Fibre composite railway sleeper design by using FE approach and optimization techniques
Awad, Ziad K. and Yusaf, Talal. 2012. "Fibre composite railway sleeper design by using FE approach and optimization techniques." Structural Engineering and Mechanics. 41 (2), pp. 231-242. https://doi.org/10.12989/sem.2012.41.2.231
Artificial neural networks approach for the prediction of thermal balance of SI engine using ethanol-gasoline blends
Kiani, Mostafa Kiani Deh, Ghobadian, Barat, Ommi, Fathollah, Najafi, Gholamhassan and Yusaf, Talal. 2012. "Artificial neural networks approach for the prediction of thermal balance of SI engine using ethanol-gasoline blends." Quirchmayr, Gerald, Basl, Josef, You, Ilsun, Xu, Lida and Weippl, Edgar (ed.) 2012 International Cross-Domain Conference and Workshop on Availability, Reliability, and Security (CD-ARES 2012). Prague, Czech Republic 20 - 24 Aug 2012 Berlin, Germany. https://doi.org/10.1007/978-3-642-32498-7_3
HCCI engine: numerical and experimental approach
Hairuddin, A. Aziz, Yusaf, Talal F. and Wandel, Andrew P.. 2012. "HCCI engine: numerical and experimental approach." Noor, M. M., Baker, Paul and Yusaf, Talal F. (ed.) USQ Combustion Meeting 2012 (26th September). Toowoomba, Australia 26 Sep 2012 Toowoomba, Australia.
Investigation of Biogas Moderate or Intense Low Oxygen Dilution (MILD) combustion on open furnace bluff-body burner
Noor, M. M., Wandel, Andrew P. and Yusaf, T. F.. 2012. "Investigation of Biogas Moderate or Intense Low Oxygen Dilution (MILD) combustion on open furnace bluff-body burner." Noor, M. M., Baker, Paul and Yusaf, Talal F. (ed.) USQ Combustion Meeting 2012 (29th August). Toowoomba, Australia 29 Aug 2012 Toowoomba, Australia.
Modelling of non-premixed turbulent combustion of hydrogen using conditional moment closure method
Noor, M. M., Hairuddin, A. Aziz, Wandel, Andrew P. and Yusaf, T. F.. 2012. "Modelling of non-premixed turbulent combustion of hydrogen using conditional moment closure method." IOP Conference Series: Materials Science and Engineering. 36 (1), pp. 1-17. https://doi.org/10.1088/1757-899X/36/1/012036
The modelling of the effect of air fuel ratio on unburned hydrocarbons for MILD combustion
Noor, M. M., Wandel, Andrew P. and Yusaf, T. F.. 2012. "The modelling of the effect of air fuel ratio on unburned hydrocarbons for MILD combustion." Noor, M. M., Rahman, M. M. and Ismail, J. (ed.) 2nd Malaysian Postgraduate Conference (MPC 2012). Gold Coast, Australia 07 - 09 Jul 2012 Sydney, Australia.
A preliminary study of control parameters for open furnace mild combustion using CFD
Noor, M. M., Wandel, Andrew P. and Yusaf, T. F.. 2012. "A preliminary study of control parameters for open furnace mild combustion using CFD." Noor, M. M., Rahman, M. M. and Ismail, J. (ed.) 2nd Malaysian Postgraduate Conference (MPC 2012). Gold Coast, Australia 07 - 09 Jul 2012 Sydney, Australia.
Mild combustion: a technical review towards open furnace combustion
Noor, M. M., Wandel, Andrew P. and Yusaf, T. F.. 2012. "Mild combustion: a technical review towards open furnace combustion." Noor, M. M., Rahman, M. M. and Ismail, J. (ed.) 2nd Malaysian Postgraduate Conference (MPC 2012). Gold Coast, Australia 07 - 09 Jul 2012 Sydney, Australia.
Numerical investigation of influence of air and fuel dilution for open furnace MILD combustion burner
Noor, M. M., Wandel, Andrew P. and Yusaf, T. F.. 2012. "Numerical investigation of influence of air and fuel dilution for open furnace MILD combustion burner." 2012 Southern Regional Engineering Conference (SREC 2012). Toowoomba, Australia 01 Sep 2012 Canberra, Australia.
Numerical investigation of flow instability in shock tube due to shock wave-contact surface interactions
Al-Falahi, Amir, Yusoff, M. Z., Yusaf, Talal and Ahmed, Diyar I.. 2012. "Numerical investigation of flow instability in shock tube due to shock wave-contact surface interactions." International Journal of Numerical Methods for Heat and Fluid Flow. 22 (3), pp. 377-398. https://doi.org/10.1108/09615531211208079
Biofouling in RO system: mechanisms, monitoring and controlling
Al-Juboori, Raed A. and Yusaf, Talal. 2012. "Biofouling in RO system: mechanisms, monitoring and controlling." Desalination. 302, pp. 1-23. https://doi.org/10.1016/j.desal.2012.06.016
Identifying the optimum process parameters for ultrasonic cellular disruption of e. coli
Al-Juboori, Raed A. and Yusaf, Talal. 2012. "Identifying the optimum process parameters for ultrasonic cellular disruption of e. coli ." International Journal of Chemical Reactor Engineering. 10 (1), pp. 1-32. https://doi.org/10.1515/1542-6580.2937
Predicting the combustion behaviour of a diesel HCCI engine using a zero-dimensional single-zone model
Hairuddin, A. Aziz, Yusaf, Talal F. and Wandel, Andrew P.. 2011. "Predicting the combustion behaviour of a diesel HCCI engine using a zero-dimensional single-zone model." Kennedy, Eric, Dlugogorski, Bogdan, Moghtaderi, Behdad and Masri, Assaad (ed.) 11th Australian Combustion Symposium (ACS 2011). Newcastle, Australia 29 Nov - 01 Dec 2011 Sydney, Australia.
Implementation of conditional moment closure using the Taylor expansion and finite differences
Noor, M. M., Hairuddin, A. Aziz, Wandel, Andrew P. and Yusaf, T. F.. 2011. "Implementation of conditional moment closure using the Taylor expansion and finite differences." 1st International Conference of Mechanical Engineering Research (ICMER 2011). Kuantan, Malaysia 05 - 07 Dec 2011 Kuantan, Malaysia.
Crude palm oil fuel for diesel-engines: experimental and ANN simulation approaches
Yusaf, T. F., Yousif, B. F. and Elawad, M. M.. 2011. "Crude palm oil fuel for diesel-engines: experimental and ANN simulation approaches." Energy. 36 (8), pp. 4871-4878. https://doi.org/10.1016/j.energy.2011.05.032
Improving the performance of ultrasonic horn reactor for deactivating microorganisms in water
Al-Juboori, R. A. and Yusaf, T. F.. 2012. "Improving the performance of ultrasonic horn reactor for deactivating microorganisms in water." 1st International Conference of Mechanical Engineering Research (ICMER 2011). Kuantan, Malaysia 05 - 07 Dec 2011 Bristol, United Kingdom. https://doi.org/10.1088/1757-899X/36/1/012037
Evaluating tractor performance and exhaust gas emissions using biodiesel from cotton seed oil
Al-lwayzy, Saddam H., Yusaf, Talal and Jensen, Troy. 2012. "Evaluating tractor performance and exhaust gas emissions using biodiesel from cotton seed oil." 1st International Conference of Mechanical Engineering Research (ICMER 2011). Kuantan, Malaysia 05 - 07 Dec 2011 United States. IOP Publishing. https://doi.org/10.1088/1757-899X/36/1/012042
Engine performance and emission analysis of LPG-SI engine with the aid of artificial neural network
Yusaf, T., Saleh, K. H. and Said, M. A.. 2011. "Engine performance and emission analysis of LPG-SI engine with the aid of artificial neural network." Proceedings of the Institution of Mechanical Engineers Part A: Journal of Power and Energy. 225 (5), pp. 591-600. https://doi.org/10.1177/0957650911402546
Simulation of instantaneous heat transfer in spark ignition internal combustion engines: unsteady thermal boundary layer modeling
Buttsworth, David R., Agrira, Abdalla, Malpress, Ray and Yusaf, Talal. 2011. "Simulation of instantaneous heat transfer in spark ignition internal combustion engines: unsteady thermal boundary layer modeling." Journal of Engineering for Gas Turbines and Power: Transactions of the ASME. 133 (2), pp. 1-5. https://doi.org/10.1115/1.4001080
Potential of renewable energy alternatives in Australia
Yusaf, Talal, Goh, Steven and Borserio, J. A.. 2011. "Potential of renewable energy alternatives in Australia." Renewable and Sustainable Energy Reviews. 15 (5), pp. 2214-2221. https://doi.org/10.1016/j.rser.2011.01.018
Algae as a sustainable energy source for biofuel production in Iran: a case study
Najafi, Gholamhassan, Ghobadian, Barat and Yusaf, Talal F.. 2011. "Algae as a sustainable energy source for biofuel production in Iran: a case study ." Renewable and Sustainable Energy Reviews. 15 (8), pp. 3870-3876. https://doi.org/10.1016/j.rser.2011.07.010
Finite element analysis of fibre reinforce concrete beam subject to high temperature by using EURO-code models
Awad, Ziad K. and Yusaf, Talal F.. 2011. "Finite element analysis of fibre reinforce concrete beam subject to high temperature by using EURO-code models." Key Engineering Materials. 471-472, pp. 343-348. https://doi.org/10.4028/www.scientific.net/KEM.471-472.343
Investigating the efficiency of thermosonication for controlling biofouling in batch membrane systems
Al-Juboori, Raed A., Yusaf, Talal and Aravinthan, Vasanthadevi. 2012. "Investigating the efficiency of thermosonication for controlling biofouling in batch membrane systems." Desalination. 286, pp. 349-357. https://doi.org/10.1016/j.desal.2011.11.049
A hybrid EMST-modified Curl's model for turbulent combustion modelling
Noor, M. M., Wandel, Andrew P. and Yusaf, T. F.. 2011. "A hybrid EMST-modified Curl's model for turbulent combustion modelling." University of Southern Queensland's Research Evening: Showcasing USQ Research (2011). Toowoomba, Australia 17 Nov 2011
Study of random particle interactions for analysis of diffusion lengths in turbulent combustion modelling
Noor, M. M., Yusaf, T. F. and Wandel, Andrew P.. 2011. "Study of random particle interactions for analysis of diffusion lengths in turbulent combustion modelling." Kennedy, Eric, Dlugogorski, Bogdan, Moghtaderi, Behdad and Masri, Assaad (ed.) 11th Australian Combustion Symposium (ACS 2011). Newcastle, Australia 29 Nov - 01 Dec 2011 Sydney, Australia.
Mechanical treatment of microorganisms using ultrasound, shock and shear technology
Yusaf, Talal. 2011. Mechanical treatment of microorganisms using ultrasound, shock and shear technology. PhD Thesis Doctor of Philosophy. University of Southern Queensland.
Numerical simulation of inviscid transient flows in shock tube and its validations
Al-Falahi, Amir, Yusoff, M. Z. and Yusaf, T.. 2008. "Numerical simulation of inviscid transient flows in shock tube and its validations." International Journal of Mechanical, Aerospace, Industrial and Mechatronics Engineering. 2 (7), pp. 1-11.
Simulation of instantaneous heat transfer in spark ignition internal combustion engines: unsteady thermal boundary layer modelling
Buttsworth, David R., Agrira, Abdalla, Malpress, Ray and Yusaf, Talal. 2009. "Simulation of instantaneous heat transfer in spark ignition internal combustion engines: unsteady thermal boundary layer modelling." Callahan, Tim (ed.) ASME Internal Combustion Engine Division Fall Technical Conference (ICEF 2009). Lucerne, Switzerland 27 - 30 Sep 2009 United States. https://doi.org/10.1115/ICEF2009-14056
Experimental and CFD study of the effects of design parameters on Reynolds number in a short duration hypersonic test facility
Al-Falahi, Amir, Yusaf, T. and Yusoff, M. Z.. 2007. "Experimental and CFD study of the effects of design parameters on Reynolds number in a short duration hypersonic test facility." Yao, Z. H. and Yuan, M. W. (ed.) EPMESC X: Enhancement and Promotion of Computational Methods in Engineering and Science X. Sanya, China 21 - 23 Aug 2006 Berlin, Germany. https://doi.org/10.1007/978-3-540-48260-4_26
Hydrogen and natural gas comparison in diesel HCCI engines -a review
Hairuddin, A. Aziz, Wandel, Andrew P. and Yusaf, Talal. 2010. "Hydrogen and natural gas comparison in diesel HCCI engines -a review." Goh, Steven C. and Wang, Hao (ed.) 2010 Southern Region Engineering Conference (SREC 2010). Toowoomba, Australia 11 - 12 Nov 2010 Toowoomba, Australia.
Remote access laboratories in Australia and Europe
Ku, H., Ahfock, T. and Yusaf, T.. 2011. "Remote access laboratories in Australia and Europe." European Journal of Engineering Education. 36 (3), pp. 253-268. https://doi.org/10.1080/03043797.2011.578244
Performance and emission investigation of a four-stroke liquefied petroleum gas spark-ignition engine generator used in a Malaysian night market
Yusaf, Talal, Said, Mior Azman and Hussein, Ibrahim. 2010. "Performance and emission investigation of a four-stroke liquefied petroleum gas spark-ignition engine generator used in a Malaysian night market ." Proceedings of the Institution of Mechanical Engineers Part A: Journal of Power and Energy. 224 (3), pp. 339-347. https://doi.org/10.1243/09576509JPE882
CNG-diesel engine performance and exhaust emission analysis with the aid of artificial neural network
Yusaf, Talal F., Buttsworth, D. R., Saleh, Khalid H. and Yousif, B. F.. 2010. "CNG-diesel engine performance and exhaust emission analysis with the aid of artificial neural network." Applied Energy. 87 (5), pp. 1661-1669. https://doi.org/10.1016/j.apenergy.2009.10.009
Experimental and modeling investigation of the performance characteristics on diesel HCCI with hydrogen additive - a review
Supeni, E. E., Yusaf, Talal, Wandel, Andrew P., Buttsworth, David R. and Noor, M. M.. 2010. "Experimental and modeling investigation of the performance characteristics on diesel HCCI with hydrogen additive - a review." 2nd National Conference in Mechanical Engineering Research and Postgraduate Studies. Kuantan, Malaysia 03 - 04 Dec 2010 Malaysia.
Development of a small icing wind tunnel for simulating the initial stages of solid phase ice accretion
Saleh, Khalid, Buttsworth, David and Yusaf, Talal. 2010. "Development of a small icing wind tunnel for simulating the initial stages of solid phase ice accretion." Mallinson, G. D. and Cater, J. E. (ed.) 17th Australasian Fluid Mechanics Conference (AFMC 2010). Auckland, New Zealand 05 - 09 Dec 2010 Auckland, New Zealand.
How effective is microalgae treatment of nursery wastewater for nutrient removal?
Pufelski, N., Aravinthan, V. and Yusaf, T.. 2010. "How effective is microalgae treatment of nursery wastewater for nutrient removal?" Goh, Steven C. and Wang, Hao (ed.) 2010 Southern Region Engineering Conference (SREC 2010). Toowoomba, Australia 11 - 12 Nov 2010 Toowoomba, Australia.
Microalgae as alternative fuel for compression ignition (CI) Engines
Allwayzy, S. H., Yusaf, T., McCabe, B., Pittaway, P. and Aravinthan, V.. 2010. "Microalgae as alternative fuel for compression ignition (CI) Engines." Goh, Steven C. and Wang, Hao (ed.) 2010 Southern Region Engineering Conference (SREC 2010). Toowoomba, Australia 11 - 12 Nov 2010 Toowoomba, Australia.
A review of common and alternative methods for disinfection of microorganisms in water
Al-Juboori, Raed, Aravinthan, Vasantha and Yusaf, Talal. 2010. "A review of common and alternative methods for disinfection of microorganisms in water." Goh, Steven C. and Wang, Hao (ed.) 2010 Southern Region Engineering Conference (SREC 2010). Toowoomba, Australia 11 - 12 Nov 2010 Toowoomba, Australia.
Abrasive wear behaviour of epoxy composite based on kenaf fibres
Yousif, B. F. and Yusaf, Talal. 2010. "Abrasive wear behaviour of epoxy composite based on kenaf fibres." Gwidon, Stachowiak (ed.) ASIATRIB 2010: Frontiers in Tribology - Knowledge and Friendship. Perth, Australia 05 - 09 Dec 2010
Adhesive wear and frictional characteristics of UHMWPE and HDPE sliding against different counterfaces under dry contact condition
Yousif, B. F., Alsofyani, I. M. and Yusaf, Talal. 2010. "Adhesive wear and frictional characteristics of UHMWPE and HDPE sliding against different counterfaces under dry contact condition." Tribology. 4 (2), pp. 78-85. https://doi.org/10.1179/175158310X12678019274408
Universiti Tenaga Nasional short duration hypersonic test facility: calibration and verification
Al-Falahi, Amir, Yusaf, T. and Yusoff, M. Z.. 2006. "Universiti Tenaga Nasional short duration hypersonic test facility: calibration and verification." Zannetti, Luca (ed.) 8th Biennial ASME Conference on Engineering Systems Design and Analysis (ESDA 2006). Torino, Italy 04 - 07 Jul 2006 New York, NY. United States. https://doi.org/10.1115/ESDA2006-95448
Performance and exhaust emission of a diesel engine using crude palm oil as a fuel extender
El-Awad, Mohamed and Yusaf, Talal. 2004. "Performance and exhaust emission of a diesel engine using crude palm oil as a fuel extender." Journal of Energy & Environment . 3, pp. 61-68.
Heat transfer in an ultrasonic processing cell: preliminary measurements
Yusaf, Talal, Buttsworth, David R. and Deeth, Hilton C.. 2003. "Heat transfer in an ultrasonic processing cell: preliminary measurements." Emirates Journal of Agricultural Sciences . 15 (2), pp. 80-86.
Numerical computation of high speed turbulent flow using coupled solution technique with standard K-epsilon turbulence model
Ng, K. C., Yusoff, M. Z. and Yusaf, T. F.. 2005. "Numerical computation of high speed turbulent flow using coupled solution technique with standard K-epsilon turbulence model." Australian Journal of Mechanical Engineering. 2 (1), pp. 79-92.
Modeling of viscous flows in two-dimensional turbomachinery cascade via viscous-inviscid interaction method
Yusoff, M. Z., Hussein, I., Yusaf, T. and Ahmad, Z.. 2005. "Modeling of viscous flows in two-dimensional turbomachinery cascade via viscous-inviscid interaction method." Institution of Engineers, Malaysia. Journal. 66 (3), pp. 14-20.
Development status of indigenous computational fluid dynamics software for arbitrary complex geometry
Ng, K. C., Yusoff, M. Z., Yusaf, T. F. and Hussein, I.. 2005. "Development status of indigenous computational fluid dynamics software for arbitrary complex geometry." Institution of Engineers, Malaysia. Journal. 66 (4), pp. 15-22.
A quasi one-dimensional simulation of a 4 stroke spark ignition hydrogen fuelled engine
Yusaf, T. F., Yusoff, M. Z., Hussein, I. and Fong, S. H.. 2005. "A quasi one-dimensional simulation of a 4 stroke spark ignition hydrogen fuelled engine." American Journal of Applied Sciences. 2 (8), pp. 1206-1212.
Small scale power generation using a dual fuel system
Yusaf, Talal, Al-Atabi, Mushtak Talib Ali and Buttsworth, David R.. 2003. "Small scale power generation using a dual fuel system." RERIC International Energy Journal. 4 (2), pp. 129-138.
Modeling of transient heat flux in spark ignition engine during combustion and comparisons with experiments
Yusaf, T. F., Fong, S. F., Yusoff, M. Z. and Hussein, I.. 2005. "Modeling of transient heat flux in spark ignition engine during combustion and comparisons with experiments." American Journal of Applied Sciences. 2 (10), pp. 1438-1444.
Simulations of two-dimensional high speed turbulent compressible flow in a diffuser and a nozzle blade cascade
Ng, K. C., Yusoff, M. Z. and Yusaf, T. F.. 2005. "Simulations of two-dimensional high speed turbulent compressible flow in a diffuser and a nozzle blade cascade." American Journal of Applied Sciences. 2 (9), pp. 1325-1330.
Theoretical and experimental investigation of SI engine performance and exhaust emissions using ethanol-gasoline blended fuels
Yusaf, Talal, Najafi, G. and Buttsworth, David. 2009. "Theoretical and experimental investigation of SI engine performance and exhaust emissions using ethanol-gasoline blended fuels." Abidin, Izham Bin Datuk Zainal (ed.) 3rd International Conference on Energy and Environment (ICEE 2009): Advancement Towards Global Sustainability. Malacca, Malaysia 07 - 08 Dec 2009 Selangor, Malaysia. https://doi.org/10.1109/ICEENVIRON.2009.5398648
A review of radiation heat transfer measurement for diesel engines using the two-colour method
Said, Mior A., Buttsworth, D. R. and Yusaf, T. F.. 2009. "A review of radiation heat transfer measurement for diesel engines using the two-colour method." 3rd International Conference on Energy and Environment (ICEE 2009): Advancement Towards Global Sustainability. Malacca, Malaysia 07 - 08 Dec 2009 Selangor, Malaysia. https://doi.org/10.1109/ICEENVIRON.2009.5398645
Discrete particle simulation for the initial stages of ice accretion in aircraft engines: initial model development
Buttsworth, David, Saleh, Khalid and Yusaf, Talal. 2009. "Discrete particle simulation for the initial stages of ice accretion in aircraft engines: initial model development." Abidin, Izham Bin Datuk Zainal (ed.) 3rd International Conference on Energy and Environment (ICEE 2009): Advancement Towards Global Sustainability. Malacca, Malaysia 07 - 08 Dec 2009 Piscataway, NJ. United States. https://doi.org/10.1109/ICEENVIRON.2009.5398655
Instantaneous heat flux simulation of S.I. engines: comparison of unsteady thermal boundary layer modelling with experimental data
Agrira, Abdalla, Buttsworth, David R. and Yusaf, Talal. 2009. "Instantaneous heat flux simulation of S.I. engines: comparison of unsteady thermal boundary layer modelling with experimental data ." 3rd International Conference on Energy and Environment (ICEE 2009): Advancement Towards Global Sustainability. Malacca, Malaysia 07 - 08 Dec 2009 Selangor, Malaysia. https://doi.org/10.1109/ICEENVIRON.2009.5398679
Performance and exhaust emission of a SI engine fuelled with potato waste ethanol and its blends with gasoline
Najafi, G., Yusaf, T. F., Ghobadian, B., Najmeddin, V. R. and Yousif, B. F.. 2009. "Performance and exhaust emission of a SI engine fuelled with potato waste ethanol and its blends with gasoline." International Energy Journal. 10 (4), pp. 215-226.
Flow instability in shock tube due to shock wave-boundary layer-contact surface interactions, a numerical study
Al-Falahi, Amir, Yusoff, M. Z., Shuaib, N. H. and Yusaf, T.. 2009. "Flow instability in shock tube due to shock wave-boundary layer-contact surface interactions, a numerical study." European Journal of Scientific Research. 30 (1), pp. 164-176.
Adhesive wear and frictional behaviour of multilayered polyester composite based on betelnut fiber mats under wet contact conditions
Yousif, B. F., Devadas, Alvin and Yusaf, Talal. 2009. "Adhesive wear and frictional behaviour of multilayered polyester composite based on betelnut fiber mats under wet contact conditions." Surface Review and Letters. 16 (3), pp. 407-414. https://doi.org/10.1142/S0218625X09012792
Potential of bioethanol production from agricultural wastes in Iran
Najafi, G., Ghobadian, B., Tavakoli, T. and Yusaf, T.. 2009. "Potential of bioethanol production from agricultural wastes in Iran." Renewable and Sustainable Energy Reviews. 13 (6-7), pp. 1418-1427. https://doi.org/10.1016/j.rser.2008.08.010
Experimental investigation of using methanol-diesel blended fuels in diesel engine
Najafi, Gholamhassan and Yusaf, Talal. 2009. "Experimental investigation of using methanol-diesel blended fuels in diesel engine." 4th International Conference on Thermal Engineering Theory and Applications. Abu Dhabi, United Arab Emirates 12 - 14 Jan 2009 Abu Dhabi, UAE.
Performance and exhaust emissions of a gasoline engine with ethanol blended gasoline fuels using artificial neural network
Najafi, G., Ghobadian, B., Tavakoli, T., Buttsworth, D. R., Yusaf, T. F. and Faizollahnejad, M.. 2009. "Performance and exhaust emissions of a gasoline engine with ethanol blended gasoline fuels using artificial neural network ." Applied Energy. 86 (5), pp. 630-639. https://doi.org/10.1016/j.apenergy.2008.09.017
Diesel engine optimization for electric hybrid vehicles
Yusaf, Talal F.. 2009. "Diesel engine optimization for electric hybrid vehicles." Journal of Energy Resources Technology. 131 (1), pp. 12203-1-12203-4. https://doi.org/10.1115/1.3068347
Future of renewable energies in Iran
Ghobadian, Barat, Najafi, Gholamhassan, Rahimi, Hadi and Yusaf, T. F.. 2009. "Future of renewable energies in Iran." Renewable and Sustainable Energy Reviews. 13 (3), pp. 689-695. https://doi.org/10.1016/j.rser.2007.11.010
Diesterol: an environment-friendly IC engine fuel
Rahimi, Hadi, Ghobadian, Barat, Yusaf, Talal, Najafi, Gholamhasan and Khatamifar, Mahdi. 2009. "Diesterol: an environment-friendly IC engine fuel." Renewable Energy. 34 (1), pp. 335-342. https://doi.org/10.1016/j.renene.2008.04.031
Diesel engine performance and exhaust emission analysis using waste cooking biodiesel fuel with an artificial neural network
Ghobadian, B., Rahimi, H., Nikbakht, A. M., Najafi, G. and Yusaf, T. F.. 2009. "Diesel engine performance and exhaust emission analysis using waste cooking biodiesel fuel with an artificial neural network ." Renewable Energy. 34 (4), pp. 976-982. https://doi.org/10.1016/j.renene.2008.08.008
Development of a short duration hypersonic test facility at Universiti Tenaga Nasional
Al-Falahi, Amir, Yusoff, Mohd. Zamri bin and Yusaf, Talal. 2008. "Development of a short duration hypersonic test facility at Universiti Tenaga Nasional ." Institution of Engineers, Malaysia. Journal. 69 (1), pp. 19-25.
Numerical simulation of inviscid transient flows in shock tube and its validations
Al-Falahi, Amir, Yusoff, M. Z. and Yusaf, T.. 2008. "Numerical simulation of inviscid transient flows in shock tube and its validations." 2008 World Academy of Science, Engineering and Technology (WASET 2008). Heidelberg, Germany 12 - 14 Sep 2008 Istanbul, Turkey.
An experimental evaluation of shock wave strength and peak pressure in a conventional shock tube and a free-piston compressor
Al-Falahi, Amir, Yusoff, M. Z. and Yusaf, T.. 2009. "An experimental evaluation of shock wave strength and peak pressure in a conventional shock tube and a free-piston compressor." 2008 ASME International Mechanical Engineering Congress and Exposition (IMECE 2008). Boston, United States of America 31 Oct - 06 Nov 2008 Boston, MA. United States. https://doi.org/10.1115/IMECE2008-66246
Development of a high pressure compressed natural gas mixer for a 1.5 litre CNG-diesel dual engine
Noor, M. M., Kadirgama, K., Devarajan, R., Rejab, M. R. M., Zuki, N. M. and Yusaf, Talal. 2008. "Development of a high pressure compressed natural gas mixer for a 1.5 litre CNG-diesel dual engine." National Conference on Design and Concurrent Engineering (DECON) 2008. Melaka, Malaysia 28 - 29 Oct 2008 Malaysia.
Influence of material structure properties on sliding contact performance of CGRP composite
Yousif, B. F., El-Tayeb, N. S. M. and Yusaf, Talal. 2008. "Influence of material structure properties on sliding contact performance of CGRP composite." International Journal for Manufacturing Science and Technology. 10 (1), pp. 1-7.
Experimental investigation of performance and emission parameters of a small diesel engine using CNG and biodiesel
Najafi, Bahman, Pirouzpanah, Vahab, Najafi, Gholamhassan, Yusaf, Talal and Ghobadian, Barat. 2007. "Experimental investigation of performance and emission parameters of a small diesel engine using CNG and biodiesel." 13th Small Engine Technology Conference 2007. Toki Messe, Niigata, Japan 30 Oct - 01 Nov 2007 Japan.
Processing of composites using variable and fixed frequency microwave facilities
Ku, Harry S. and Yusaf, Talal. 2008. "Processing of composites using variable and fixed frequency microwave facilities." Progress in Electromagnetic Research B. 5, pp. 185-205. https://doi.org/10.2528/PIERB08011304
Numerical and experimental study to evaluate the performance of Universiti Tenaga Nasional short duration hypersonic test facility
Al-Falahi, Amir, Yusoff, M. Z. and Yusaf, T.. 2007. "Numerical and experimental study to evaluate the performance of Universiti Tenaga Nasional short duration hypersonic test facility." Jacobs, Peter A., McIntyre, Tim, Cleary, Matthew J., Buttsworth, David R., Mee, David, Clements, Rose, Morgan, Richard and Lemckert, Charles (ed.) 16th Australasian Fluid Mechanics Conference (AFMC 2007). Gold Coast, Australia 03 - 07 Dec 2007 Brisbane, Australia.
Numerical simulation of 3D transonic flow in a compressor rotor
Ng, K. C., Yusoff, M. Z. and Yusaf, T. F.. 2007. "Numerical simulation of 3D transonic flow in a compressor rotor." International Journal of Modelling and Simulation. 27 (1), pp. 74-79. https://doi.org/10.2316/Journal.205.2007.1.205-4495
Characterisation of mixing rate due to high power ultrasound
Yusaf, Talal and Buttsworth, David R.. 2007. "Characterisation of mixing rate due to high power ultrasound." Ultrasonics Sonochemistry. 14 (2), pp. 266-274. https://doi.org/10.1016/j.ultsonch.2006.04.008
An investigation on the improvement of the operation of Tenom Pangi HPP cooling power system
Hamid, H. A., Yusaf, T. and Yusof, Z. M.. 2006. "An investigation on the improvement of the operation of Tenom Pangi HPP cooling power system." Hussein, Ibrahim (ed.) International Conference on Energy and Environment 2006 (ICEE 2006). Kajang, Malaysia 28 - 30 Aug 2006 Malaysia.
Flow and transient heat transfer in a high speed free piston tunnel: CFD simulations on turbulent and laminar flow conditions
Zakaria, S., Yusaf, T. and Yusoff, M. Z.. 2006. "Flow and transient heat transfer in a high speed free piston tunnel: CFD simulations on turbulent and laminar flow conditions." Haik, Yousef (ed.) 2nd International Conference on Thermal Engineering Theory and Applications (ICTEA '06). Al Ain, United Arab Emirates 03 - 06 Jan 2006 United Arab Emirates.
Experimental investigation of free convection heat transfer with entrance restriction placed at top of a vertical circular tube
Mohammed, H., Yusaf, T. and Salman, Y.. 2006. "Experimental investigation of free convection heat transfer with entrance restriction placed at top of a vertical circular tube." Zannetti, Luca (ed.) 8th Biennial ASME Conference on Engineering Systems Design and Analysis (ESDA 2006). Torino, Italy 04 - 07 Jul 2006 New York, NY, United States. https://doi.org/10.1115/ESDA2006-95229
Heat transfer by mixed convection opposing laminar flow from the inside surface of uniformly heated inclined circular tube
Mohammed, H. and Yusaf, T.. 2006. "Heat transfer by mixed convection opposing laminar flow from the inside surface of uniformly heated inclined circular tube ." Zannetti, Luca (ed.) 8th Biennial ASME Conference on Engineering Systems Design and Analysis (ESDA 2006). Torino, Italy 04 - 07 Jul 2006 New York, NY. United States. https://doi.org/10.1115/ESDA2006-95202
The effects of load and velocity on friction and interface temperature of CGRP sliding against smooth stainless steel
Yousif, B. F., El-Tayeb, N. S. M. and Yusaf, Talal. 2006. "The effects of load and velocity on friction and interface temperature of CGRP sliding against smooth stainless steel." Zannetti, Luca (ed.) 8th Biennial ASME Conference on Engineering Systems Design and Analysis (ESDA 2006). Torino, Italy 04 - 07 Jul 2006 Italy.
Development of a 3D CFD model to investigate the effect of the mixing quality on the CNG-diesel engine performance
Yusaf, Talal and Yusoff, Mohammed Zamri. 2000. "Development of a 3D CFD model to investigate the effect of the mixing quality on the CNG-diesel engine performance." The International Conference and Exhibition and Natural Gas Vehicles (2000). Yokohama, Japan 17 - 19 Oct 2000 Malaysia.
Experimental investigation for the design of ECU for a single cylinder engine using dual-fuel (CNG-diesel)
Yusaf, Talal F. and Talib, Mushtak. 2003. "Experimental investigation for the design of ECU for a single cylinder engine using dual-fuel (CNG-diesel)." 2003 Asian Conference on Sensors (AsiaSENSE 2003). Malaysia 18 Jul 2003 United States. https://doi.org/10.1109/ASENSE.2003.1225042
Experimental Investigation of A Single Cylinder Diesel Engine as A Hybrid Power Unit for A Series Hybrid Electric Vehicle
Al-Atabi, Mushtak Talib and Yusaf, Talal F.. 2002. "Experimental Investigation of A Single Cylinder Diesel Engine as A Hybrid Power Unit for A Series Hybrid Electric Vehicle." 2002 Student Conference on Research and Development (SCOReD 2002). Malaysia 16 - 17 Jul 2002 United States. https://doi.org/10.1109/SCORED.2002.1033107
Level Control Experiment via Internet
Salleh, Hanim, Yusaf, Talal F. and Azlan, M. Khafif. 2000. "Level Control Experiment via Internet." 2000 IEEE Region 10 International Conference (TENCON 2000). Kuala Lumpur 24 - 27 Sep 2000 IEEE (Institute of Electrical and Electronics Engineers). https://doi.org/10.1109/TENCON.2000.888798
Combustion Processes of Rice Husks for Energy
Ismail, Ahmad-Faris, Yusaf, Talal F., Mahdi, Faisal M. A. and Shamsuddin, Abdul Halim. 1997. "Combustion Processes of Rice Husks for Energy." RERIC International Energy Journal. 19 (2), pp. 63-75.
Design Modification of High Speed Diesel Engine to Accommodate Compressed Natural Gas
Yusaf, Talal F., Shamsuddin, Abdul Halim, Ali, Yusoff and Ismail, Ahmad Faris. 1996. "Design Modification of High Speed Diesel Engine to Accommodate Compressed Natural Gas." RERIC International Energy Journal. 18 (1), pp. 19-26.