Performance and exhaust emission of a SI engine fuelled with potato waste ethanol and its blends with gasoline
Article
Article Title | Performance and exhaust emission of a SI engine fuelled with potato waste ethanol and its blends with gasoline |
---|---|
ERA Journal ID | 3484 |
Article Category | Article |
Authors | Najafi, G. (Author), Yusaf, T. F. (Author), Ghobadian, B. (Author), Najmeddin, V. R. (Author) and Yousif, B. F. (Author) |
Journal Title | International Energy Journal |
Journal Citation | 10 (4), pp. 215-226 |
Number of Pages | 12 |
Year | 2009 |
Place of Publication | PathumThani,Thailand |
ISSN | 1513-718X |
Web Address (URL) | http://www.rericjournal.ait.ac.th/index.php/reric |
Abstract | The main aim of this study is to investigate the performance and the pollutant emissions of a four stroke SI engine operating on different ethanol-gasoline blends (0-20%). Fuel properties of ethanol–gasoline blended were examined by the standard ASTM methods. The results showed that increasing the ethanol content in the blend fuel will decrease the heating value of the blended fuel and increase the octane number. Exhaust gas emissions were evaluated and analyzed for Unburned Hydrocarbons (UHC), Carbon Dioxide (CO2), Carbon Monoxide (CO), Oxygen (O2) and Oxide of Nitrogen NOx at different engine speeds and loads (1000-5000 rpm). The results revealed that using ethanol-gasoline blended fuels will marginally increase the brake power and the torque output, the brake thermal efficiency, the relative air–fuel ratio and the volumetric efficiency. Moreover, using ethanol-gasoline blends will decrease the brake specific fuel consumption, CO and HC emissions concentration. This improvement was due to the high oxygen percentage in the ethanol. However the CO2, NOx concentration and the exhaust gas temperature was noticed to be increased. |
Keywords | ethanol; engine performance; gasoline; ethanol-gasoline blends; exhaust emissions; SI engine; petrol |
ANZSRC Field of Research 2020 | 401703. Energy generation, conversion and storage (excl. chemical and electrical) |
400402. Chemical and thermal processes in energy and combustion | |
400799. Control engineering, mechatronics and robotics not elsewhere classified | |
Public Notes | Files associated with this item cannot be displayed due to copyright restrictions. |
Byline Affiliations | Tarbiat Modares University, Iran |
National Centre for Engineering in Agriculture | |
Mazandaran University of Science and Technology, Iran | |
University of Nottingham, United Kingdom |
https://research.usq.edu.au/item/9z65q/performance-and-exhaust-emission-of-a-si-engine-fuelled-with-potato-waste-ethanol-and-its-blends-with-gasoline
2047
total views10
total downloads13
views this month0
downloads this month
Export as
Related outputs
Theoretical study of the effect of orientations and fibre volume on the thermal insulation capability of reinforced polymer composites
Shalwan, Abdullah, Alajmi, Abdalrahman and Yousif, Belal. 2024. "Theoretical study of the effect of orientations and fibre volume on the thermal insulation capability of reinforced polymer composites." Reviews on Advanced Materials Science. 63 (1). https://doi.org/10.1515/rams-2023-0190Finite element analysis and experimental validation of polymer–metal contacts in block-on-ring configuration
Awwad, K. Y. Eayal, Fallahnezhad, Khosro, Yousif, B. F., Mostafa, Ahmad, Alajarmeh, Omar, Shalwan, A. and Zeng, Xuesen. 2024. "Finite element analysis and experimental validation of polymer–metal contacts in block-on-ring configuration." Friction. 12 (3), pp. 554-568. https://doi.org/10.1007/s40544-023-0795-xRevolutionizing procurement: Unveiling next-gen supplier strategies in UAE's oil & gas sector
Alhammadi, Ali, Yusaf, Talal, Soar, Jeffrey, Ali, Bashar Mahmood, Kadirgama, Kumaran and Yousif, Belal F. 2024. "Revolutionizing procurement: Unveiling next-gen supplier strategies in UAE's oil & gas sector." The Extractive Industries and Society. 17. https://doi.org/10.1016/j.exis.2024.101428Influence of Natural Gas and Hydrogen Properties on Internal Combustion Engine Performance, Combustion, and Emissions: A Review
Algayyim, Sattar Jabbar Murad, Saleh, Khalid, Wandel, Andrew P, Fattah, Islam Md Rizwanul, Yusaf, Talal and Alrazen, Hayder A.. 2024. "Influence of Natural Gas and Hydrogen Properties on Internal Combustion Engine Performance, Combustion, and Emissions: A Review." Fuel: the science and technology of fuel and energy. 632. https://doi.org/10.1016/j.fuel.2023.130844Investigation on Three-Body Abrasion Resistance of Mild Steel Soil Slurry Condition-Simulating Agricultural Condition
Alsaeed, Talal, Alajmi, Ayedh Eid, Alotaibi, Jasem Ghanem and Yousif, Belal F.. 2023. "Investigation on Three-Body Abrasion Resistance of Mild Steel Soil Slurry Condition-Simulating Agricultural Condition." Advances in Materials Science and Engineering. 2023. https://doi.org/10.1155/2023/5616909Redefining procurement paradigms: A critical review of buyer-supplier dynamics in the global petroleum and natural gas industry
Alhammadi, Ali, Soar, Jeffrey, Yusaf, Talal, Ali, Bashar Mahmood and Kadirgama, Kumaran. 2023. "Redefining procurement paradigms: A critical review of buyer-supplier dynamics in the global petroleum and natural gas industry." The Extractive Industries and Society. 16. https://doi.org/10.1016/j.exis.2023.101351Investigating the lap shear adhesion of coir and glass-fibre reinforced epoxy bonding to mild steel with varying volume fractions
Alajmi, Ayedh Eid, Alsaeed, Talal, Alotaibi, Jasem Ghanem, Srelam, Jayanth Kumar and Yousif, Belal F.. 2023. "Investigating the lap shear adhesion of coir and glass-fibre reinforced epoxy bonding to mild steel with varying volume fractions." Frontiers in Mechanical Engineering. 9. https://doi.org/10.3389/fmech.2023.1232643Sugarcane Biomass as a Source of Biofuel for Internal Combustion Engines (Ethanol and Acetone-Butanol-Ethanol): A Review of Economic Challenges
Algayyim, Sattar Jabbar Murad, Yusaf, Talal, Hamza, Naseer H., Wandel, Andrew P., Fattah, I. M. Rizwanul, Laimon, Mohamd and Rahman, S. M. Ashrafur. 2022. "Sugarcane Biomass as a Source of Biofuel for Internal Combustion Engines (Ethanol and Acetone-Butanol-Ethanol): A Review of Economic Challenges." Energies. 15 (22), pp. 1-17. https://doi.org/10.3390/en15228644Experimental Study on the Efficiency Improvement of Flat Plate Solar Collectors Using Hybrid Nanofluids Graphene/Waste Cotton
Mahamude, Abu Shadate Faisal, Harun, Wan Sharuzi Wan, Kadirgama, Kumaran, Ramasamy, Devarajan, Farhana, Kaniz, Saleh, Khalid and Yusaf, Talal. 2022. "Experimental Study on the Efficiency Improvement of Flat Plate Solar Collectors Using Hybrid Nanofluids Graphene/Waste Cotton." Energies. 15 (7), pp. 1-27. https://doi.org/10.3390/en15072309Machinability of Polymeric Composites and Future Reinforcements — A Review
Shalwan, Abdullah, Alsaeed, Talal and Yousif, Belal. 2022. "Machinability of Polymeric Composites and Future Reinforcements — A Review." Journal of Materials Science and Chemical Engineering. 10 (5), pp. 40-72. https://doi.org/10.4236/msce.2022.105004System dynamics modelling to assess the impact of renewable energy systems and energy efficiency on the performance of the energy sector
Laimon, Mohamd, Mai, Thanh, Goh, Steven and Yusaf, Talal. 2022. "System dynamics modelling to assess the impact of renewable energy systems and energy efficiency on the performance of the energy sector." Renewable Energy. 193, pp. 1041-1048. https://doi.org/10.1016/j.renene.2022.05.041A systems thinking approach to address sustainability challenges to the energy sector
Laimon, M., Yusaf, Talal, Mai, T., Goh, S. and Alrefae, Waleed. 2022. "A systems thinking approach to address sustainability challenges to the energy sector." International Journal of Thermofluids. 15, pp. 1-13. https://doi.org/10.1016/j.ijft.2022.100161Theoretical Study of the Effect of Fibre Porosity on the Heat Conductivity of Reinforced Gypsum Composite Material
Shalwan, A., Alajmi, Abdalrahman and Yousif, B. F.. 2022. "Theoretical Study of the Effect of Fibre Porosity on the Heat Conductivity of Reinforced Gypsum Composite Material." Polymers. 14 (19), pp. 1-23. https://doi.org/10.3390/polym14193973Effects of exhaust gas recirculation (EGR) on a diesel engine fuelled with palm-biodiesel
Yasin, Mohd Hafizil Mat, Mamat, Rizalman, Yusop, Ahmad Fitri, Paruka, Perowansa, Yusaf, Talal and Najafi, Gholamhassan. 2015. "Effects of exhaust gas recirculation (EGR) on a diesel engine fuelled with palm-biodiesel." Energy Procedia. 75, pp. 30-36. https://doi.org/10.1016/j.egypro.2015.07.131Development of micro-scale biomass-fuelled CHP system using stirling engine
Arashnia, Ilva, Najafi, Gholamhassan, Ghobadian, Barat, Yusaf, Talal, Mamat, Rizalman and Kettner, Maurice. 2015. "Development of micro-scale biomass-fuelled CHP system using stirling engine." Energy Procedia. 75, pp. 1108-1113. https://doi.org/10.1016/j.egypro.2015.07.505Optimization of combustion in micro combined heat and power (mCHP) system with the biomass-Stirling engine using SiO2 and Al2O3 nanofluids
Najafi, G., Hoseini, S. S., De Goey, L. P. H. and Yusaf, Talal. 2020. "Optimization of combustion in micro combined heat and power (mCHP) system with the biomass-Stirling engine using SiO2 and Al2O3 nanofluids." Applied Thermal Engineering. 169 (114936), pp. 1-9. https://doi.org/10.1016/j.applthermaleng.2020.114936Analysis of Particulate Matter (PM) Emissions in Diesel Engines Using Palm Oil Biodiesel Blended with Diesel Fuel
Yusop, Ahmad Fitri, Mamat, Rizalman, Yusaf, Talal, Najafi, Gholamhassan, Yasin, Mohd Hafizil Mat and Khathri, Akasyah Mohd. 2018. "Analysis of Particulate Matter (PM) Emissions in Diesel Engines Using Palm Oil Biodiesel Blended with Diesel Fuel." Energies. 11 (5), pp. 1-25. https://doi.org/10.3390/en11051039Alcohol and ether as alternative fuels in spark ignition engine: A review
Awad, Omar I., Mamat, R., Ali, Obed M., Sidik, N. A. C., Yusaf, T., Kadirgama, K. and Kettner, Maurice. 2018. "Alcohol and ether as alternative fuels in spark ignition engine: A review." Renewable and Sustainable Energy Reviews. 82 (Part 3), pp. 2586-2605. https://doi.org/10.1016/j.rser.2017.09.074Ailanthus altissima (tree of heaven) seed oil: Characterisation and optimisation of ultrasonication-assisted biodiesel production
Hoseini, S. S., Najafi, G., Ghobadian, B., Mamat, R., Ebadi, M. T. and Yusaf, Talal. 2018. "Ailanthus altissima (tree of heaven) seed oil: Characterisation and optimisation of ultrasonication-assisted biodiesel production." Fuel: the science and technology of fuel and energy. 220, pp. 621-630. https://doi.org/10.1016/j.fuel.2018.01.094Economic and Environmental Impact of Energy Saving in Healthcare Buildings
Garcia-Sanz-Calcedo, Justo, Al-Kassir, Awf and Yusaf, Talal. 2018. "Economic and Environmental Impact of Energy Saving in Healthcare Buildings." Applied Sciences. 8 (3), pp. 1-13. https://doi.org/10.3390/app8030440The effect of inlet temperature and spark timing on thermo-mechanical, chemical and the total exergy of an SI engine using bioethanol-gasoline blends
Kiani, Mostafa Kiani Deh, Rostami, Sajad, Eslami, Maryam, Yusaf, Talal and Sendilvelan, Subramanian. 2018. "The effect of inlet temperature and spark timing on thermo-mechanical, chemical and the total exergy of an SI engine using bioethanol-gasoline blends." Energy Conversion and Management. 165, pp. 344-353. https://doi.org/10.1016/j.enconman.2018.03.066An Experimental Technology of Drying and Clean Combustion of Biomass Residues
Al-Kassir, Awf, Coelho, Pedro, Garcia-Sanz-Calcedo, Justo, Moral, Francisco J., Al-Karany, Raul Kassir and Yusaf, Talal. 2018. "An Experimental Technology of Drying and Clean Combustion of Biomass Residues." Applied Sciences. 8 (6), pp. 1-10. https://doi.org/10.3390/app8060905The Effects of Camelina 'Soheil' as a Novel Biodiesel Fuel on the Performance and Emission Characteristics of Diesel Engine
Hoseini, Seyed Salar, Najafi, Gholamhassam, Ghobadian, Barat, Yusaf, Talal and Ebadi, Mohammad Taghi. 2018. "The Effects of Camelina 'Soheil' as a Novel Biodiesel Fuel on the Performance and Emission Characteristics of Diesel Engine." Applied Sciences. 8 (6), pp. 1-20. https://doi.org/10.3390/app8061010Experimental and numerical analysis of flow and heat transfer characteristics of EGR cooler in diesel engine
Hoseini, S. S., Najafi, G., Ghobadian, Barat and Yusaf, Talal. 2018. "Experimental and numerical analysis of flow and heat transfer characteristics of EGR cooler in diesel engine." Applied Thermal Engineering. 140, pp. 745-758. https://doi.org/10.1016/j.applthermaleng.2018.05.058An overview of marine macroalgae as bioresource
Sudhakar, K., Mamat, R., Samykano, M., Azmi, W. H., Ishak, W. F. W. and Yusaf, Talal. 2018. "An overview of marine macroalgae as bioresource." Renewable and Sustainable Energy Reviews. 91, pp. 165-179. https://doi.org/10.1016/j.rser.2018.03.100Novel environmentally friendly fuel: The effects of nanographene oxide additives on the performance and emission characteristics of diesel engines fuelled with Ailanthus altissima biodiesel
Hoseini, S. S., Najafi, G., Ghobadian, B., Mamat, R., Ebadi, M. T. and Yusaf, Talal. 2018. "Novel environmentally friendly fuel: The effects of nanographene oxide additives on the performance and emission characteristics of diesel engines fuelled with Ailanthus altissima biodiesel." Renewable Energy. 125, pp. 283-294. https://doi.org/10.1016/j.renene.2018.02.104Characterization of biodiesel production (ultrasonic-assisted) from evening-primroses (Oenothera lamarckiana) as novel feedstock and its effect on CI engine parameters
Hoseini, S. S., Najafi, G., Ghobadian, B., Mamat, R., Ebadi, M. T. and Yusaf, Talal. 2019. "Characterization of biodiesel production (ultrasonic-assisted) from evening-primroses (Oenothera lamarckiana) as novel feedstock and its effect on CI engine parameters." Renewable Energy. 130, pp. 50-60. https://doi.org/10.1016/j.renene.2018.06.042The Impacts of Water Pricing and Non-Pricing Policies on Sustainable Water Resources Management: A Case of Ghorveh Plain at Kurdistan Province, Iran
Asaadi, Mohammad Ali, Mortazavi, Seyed Abolghasem, Zamani, Omid, Najafi, Gholam Hassan, Yusaf, Talal and Hoseini, Seyed Salar. 2019. "The Impacts of Water Pricing and Non-Pricing Policies on Sustainable Water Resources Management: A Case of Ghorveh Plain at Kurdistan Province, Iran." Energies. 12 (14), pp. 1-16. https://doi.org/10.3390/en12142667Optimization of an Ultrasonic-Assisted Biodiesel Production Process from One Genotype of Rapeseed (TERI (OE) R-983) as a Novel Feedstock Using Response Surface Methodology
Almasi, Sara, Ghobadian, Barat, Najafi, Gholam Hassan, Yusaf, Talal, Soufi, Masoud Dehghani and Hoseini, Seyed Salar. 2019. "Optimization of an Ultrasonic-Assisted Biodiesel Production Process from One Genotype of Rapeseed (TERI (OE) R-983) as a Novel Feedstock Using Response Surface Methodology." Energies. 12 (14), pp. 1-14. https://doi.org/10.3390/en12142656Performance Investigation of Solar ORC Using Different Nanofluids
Loni, Reyhaneh, Najafi, Gholamhassan, Asli-Ardeh, Ezzatollah Askari, Ghobadian, Barat, Le Roux, Willem G. and Yusaf, Talal. 2019. "Performance Investigation of Solar ORC Using Different Nanofluids." Applied Sciences. 9 (15), pp. 1-23. https://doi.org/10.3390/app9153048Performance and emission characteristics of a CI engine using nano particles additives in biodiesel-diesel blends and modeling with GP approach
Ghanbari, M., Najafi, G., Ghobadian, B., Yusaf, T., Carlucci, A. P. and Kiani Deh Kiani, M.. 2017. "Performance and emission characteristics of a CI engine using nano particles additives in biodiesel-diesel blends and modeling with GP approach." Fuel: the science and technology of fuel and energy. 202, pp. 699-716. https://doi.org/10.1016/j.fuel.2017.04.117Performance Assessment of a Solar Dryer System Using Small Parabolic Dish and Alumina/Oil Nanofluid: Simulation and Experimental Study
Arkian, Amir Hossein, Najafi, Gholamhassan, Gorjian, Shiva, Loni, Reyhaneh, Bellos, Evangelos and Yusaf, Talal. 2019. "Performance Assessment of a Solar Dryer System Using Small Parabolic Dish and Alumina/Oil Nanofluid: Simulation and Experimental Study." Energies. 12 (24), pp. 1-22. https://doi.org/10.3390/en12244747Effects of biodiesel fuel obtained from Salvia macrosiphon oil (ultrasonic-assisted) on performance and emissions of diesel engine
Hoseini, S. S., Najaf, G., Ghobadian, B., Rahimi, A., Yusaf, Talal, Mamat, Rizalman, Sidik, N. A. C. and Azmi, W. H.. 2017. "Effects of biodiesel fuel obtained from Salvia macrosiphon oil (ultrasonic-assisted) on performance and emissions of diesel engine." Energy. 131, pp. 289-296. https://doi.org/10.1016/j.energy.2017.04.150Effects of physicochemical properties of biodiesel fuel blends with alcohol on diesel engine performance and exhaust emissions: A review
Zaharin, M. S. M, Abdullah, N. R., Najafi, G., Sharudin, H. and Yusaf, T.. 2017. "Effects of physicochemical properties of biodiesel fuel blends with alcohol on diesel engine performance and exhaust emissions: A review." Renewable and Sustainable Energy Reviews. 79, pp. 475-493. https://doi.org/10.1016/j.rser.2017.05.035Analysis of the Average Annual Consumption of Water in the Hospitals of Extremadura (Spain)
Garcia-Sanz-Calcedo, Justo, Lopez-Rodriguez, Fernando, Yusaf, Talal and Al-Kassir, Awf. 2017. "Analysis of the Average Annual Consumption of Water in the Hospitals of Extremadura (Spain)." Energies. 10 (4), pp. 1-10. https://doi.org/10.3390/en10040479Dependence of the Microporosity of Activated Carbons on the Lignocellulosic Composition of the Precursors
Roman, Silvia, Ledesma, Beatriz, Alvarez-Murillo, Andres, Al-Kassir, Awf and Yusaf, Talal. 2017. "Dependence of the Microporosity of Activated Carbons on the Lignocellulosic Composition of the Precursors." Energies. 10 (4), pp. 1-11. https://doi.org/10.3390/en10040542Treatment of Slaughterhouse Waste Water Mixed with Serum from Lacteal Industry of Extremadura in Spain to Produce Clean Energy
Marcos, A. C., Al-Kassir, A., Cuadros, Francisco and Yusaf, Talal. 2017. "Treatment of Slaughterhouse Waste Water Mixed with Serum from Lacteal Industry of Extremadura in Spain to Produce Clean Energy." Energies. 10 (6), pp. 1-15. https://doi.org/10.3390/en10060765Response surface methodology (RSM) based multi-objective optimization of fusel oil-gasoline blends at different water content in SI engine
Awad, Omar I., Mamat, R., Ali, Obed M., Azmi, W. H., Kadirgama, K., Yusri, I. M., Leman, A. M. and Yusaf, T.. 2017. "Response surface methodology (RSM) based multi-objective optimization of fusel oil-gasoline blends at different water content in SI engine." Energy Conversion and Management. 150, pp. 222-241. https://doi.org/10.1016/j.enconman.2017.07.047A Comprehensive Review on Efficiency Enhancement of Solar Collectors Using Hybrid Nanofluids
Mahamude, Abu Shadate Faisal, Kamarulzaman, Muhamad Kamal, Harun, Wan Sharuzi Wan, Kadirgama, Kumaran, Ramasamy, Devarajan, Farhana, Kaniz, Bakar, Rosli Abu, Yusaf, Talal, Subramanion, Sivarao and Yousif, Belal. 2022. "A Comprehensive Review on Efficiency Enhancement of Solar Collectors Using Hybrid Nanofluids." Energies. 15 (4), pp. 1-25. https://doi.org/10.3390/en15041391Hydrogen Energy Demand Growth Prediction and Assessment (2021–2050) Using a System Thinking and System Dynamics Approach
Yusaf, Talal, Laimon, Mohamd, Alrefae, Waleed, Kadirgama, Kumaran, Al Dhahad, Hayder, Ramasamy, Devarajan, Kamarulzaman, Mohd Kamal and Yousif, Belal. 2022. "Hydrogen Energy Demand Growth Prediction and Assessment (2021–2050) Using a System Thinking and System Dynamics Approach." Applied Sciences. 12 (2), pp. 1-16. https://doi.org/10.3390/app12020781Experimental analysis on the performance, combustion/emission characteristics of a DI diesel engine using hydrogen in dual fuel mode
Bakar, R.A., Widudo, Kadirgama, K., Ramasamy, D., Yusaf, Talal, Kamarulzaman, M.K., Sivaraos, Aslfattahi, Navid, Samylingam, L. and Alwayzy, Sadam H.. 2022. "Experimental analysis on the performance, combustion/emission characteristics of a DI diesel engine using hydrogen in dual fuel mode." International Journal of Hydrogen Energy. 52 (Part C), pp. 843-860. https://doi.org/10.1016/j.ijhydene.2022.04.129Experimental and numerical study to develop TRANSYS model for an active flat plate solar collector with an internally serpentine tube receiver
Al-Manea, Ahmed, Al-Rbaihat, Raed, Kadhim, Hakim T, Alahmer, Ali, Yusaf, Talal and Egab, Karim. 2022. "Experimental and numerical study to develop TRANSYS model for an active flat plate solar collector with an internally serpentine tube receiver." International Journal of Thermofluids. 15, pp. 1-9. https://doi.org/10.1016/j.ijft.2022.100189Numerical analysis of hybrid nanofluid natural convection in a wavy walled porous enclosure: Local thermal non-equilibrium model
Kadhim, Hakim T., Al-Manea, Ahmed, Al-Shamani, Ali Najah and Yusaf, Talal. 2022. "Numerical analysis of hybrid nanofluid natural convection in a wavy walled porous enclosure: Local thermal non-equilibrium model." International Journal of Thermofluids. 15, pp. 1-10. https://doi.org/10.1016/j.ijft.2022.100190Analysis of heat transfer and fluid flow in a microchannel heat sink with sidewall dimples and fillet profile
Okab, Abdullah K., Hasan, Hayder M., Hamzah, Mushtaq, Egab, Karim, Al-Manea, Ahmed and Yusaf, Talal. 2022. "Analysis of heat transfer and fluid flow in a microchannel heat sink with sidewall dimples and fillet profile." International Journal of Thermofluids. 15, pp. 1-8. https://doi.org/10.1016/j.ijft.2022.100192Tribological behavior of mild steel under canola biolubricant conditions
Shalwan, A., Yousif, B. F., Alajmi, F. H. and Alajmi, M.. 2021. "Tribological behavior of mild steel under canola biolubricant conditions." Advances in Tribology. 2021, pp. 1-13. https://doi.org/10.1155/2021/3795831Tribological studies of bamboo fibre reinforced epoxy composites using a BOD technique
Alajmi, Ayedh Eid, Alotaibi, Jasem Gh., Yousif, B. F. and Nirmal, Umar. 2021. "Tribological studies of bamboo fibre reinforced epoxy composites using a BOD technique." Polymers. 13 (15). https://doi.org/10.3390/polym13152444Epoxy and polyester composites’ characteristics under tribological loading conditions
Alotaibi, Jasem Ghanem, Alajmi, Ayedh Eid, Mehoub, Gabrel A. and Yousif, Belal F.. 2021. "Epoxy and polyester composites’ characteristics under tribological loading conditions." Polymer. 13. https://doi.org/10.3390/polym13142230Tribological Performance of Materials Under Bio-Three Body Abrasion
Alotaibi, Jasem G., Omer, Ako K., Salih, Nbhan D. and Yousif, Belal F.. 2020. "Tribological Performance of Materials Under Bio-Three Body Abrasion." American Journal of Applied Sciences. 17 (1), pp. 161-170. https://doi.org/10.3844/ajassp.2020.161.170Effect of Fibre Content on Compressive and Flexural Properties of Coconut Fibre Reinforced Epoxy Composites
Alotaibi, Jasem G., Alajmi, Ayedh Eid, Yousif, Belal F. and Salih, Nbhan D.. 2020. "Effect of Fibre Content on Compressive and Flexural Properties of Coconut Fibre Reinforced Epoxy Composites." American Journal of Applied Sciences. 17 (1), pp. 141-155. https://doi.org/10.3844/ajassp.2020.141.155Physical and mechanical properties of bamboo fibre/polyester composites subjected to moisture and hygrothermal conditions
Azwa, Z. N. and Yousif, B. F.. 2019. "Physical and mechanical properties of bamboo fibre/polyester composites subjected to moisture and hygrothermal conditions." Proceedings of the Institution of Mechanical Engineers Part L: Journal of Materials, Design and Applications. 233 (6). https://doi.org/10.1177/1464420717704221Influence of Graphene Nanoplatelets on Mechanical Properties and Adhesive Wear Performance of Epoxy-Based Composites
Eayal Awwad, K. Y., Yousif, B. F., Fallahnezhad, Khosro, Saleh, Khalid and Zeng, Xuesen. 2021. "Influence of Graphene Nanoplatelets on Mechanical Properties and Adhesive Wear Performance of Epoxy-Based Composites." Friction. 9 (4), pp. 856-875. https://doi.org/10.1007/s40544-020-0453-5Tribological investigation of frictional behaviour of mild steel under canola bio-lubricant conditions
Shalwan, A., Yousif, B. F., Alajmi, F. H., Alrashdana, K. R. and Alajmi, M.. 2020. "Tribological investigation of frictional behaviour of mild steel under canola bio-lubricant conditions." Tribology in Industry. 42 (3), pp. 481-493. https://doi.org/10.24874/ti.895.05.20.09Energy sector development: system dynamics analysis
Laimon, Mohamd, Mai, Thanh, Goh, Steven and Yusaf, Talal. 2019. "Energy sector development: system dynamics analysis." Applied Sciences. 10 (1), pp. 1-19. https://doi.org/10.3390/app10010134The influence of emulsified water fuel containing fresh water microalgae on diesel engine performance, combustion, vibration and emission
Al-lwayzy, Saddam H., Yusaf, Talal, Saleh, Khalid and Yousif, Belal. 2019. "The influence of emulsified water fuel containing fresh water microalgae on diesel engine performance, combustion, vibration and emission." Energies. 12 (13), pp. 1-17. https://doi.org/10.3390/en12132546Mixtures of n-butanol and iso-butanol blended with diesel: experimental investigation of combustion characteristics, engine performance and emission levels in a compression ignition engine
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P. and Yusaf, Talal. 2021. "Mixtures of n-butanol and iso-butanol blended with diesel: experimental investigation of combustion characteristics, engine performance and emission levels in a compression ignition engine." Biofuels. 12 (4), pp. 439-448. https://doi.org/10.1080/17597269.2018.1493565Pulsed ultrasound as an energy saving mode for ultrasound treatment of surface water with terrestrial aquatic carbon
Al-juboori, Raed A., Yusaf, Talal and Bowtell, Les. 2018. "Pulsed ultrasound as an energy saving mode for ultrasound treatment of surface water with terrestrial aquatic carbon." Desalination and Water Treatment. 135, pp. 167-176. https://doi.org/10.5004/dwt.2018.23173Toughening of brittle polyester with functionalized halloysite nanocomposites
Albdiry, M. T. and Yousif, B. F.. 2019. "Toughening of brittle polyester with functionalized halloysite nanocomposites." Composites Part B: Engineering. 160, pp. 94-109. https://doi.org/10.1016/j.compositesb.2018.10.032The influence of fibre orientation on tribological performance of jute fibre reinforced epoxy composites considering different mat orientations
Alshammari, F. Z., Saleh, K. H., Yousif, B. F., Alajmi, A., Shalwan, A. and Alotaibi, J. G.. 2018. "The influence of fibre orientation on tribological performance of jute fibre reinforced epoxy composites considering different mat orientations." Tribology in Industry. 40 (3), pp. 335-348. https://doi.org/10.24874/ti.2018.40.03.01Fracture behaviour of bamboo fiber reinforced epoxy composites
Khan, Ziaullah, Yousif, B. F. and Islam, Mainul. 2017. "Fracture behaviour of bamboo fiber reinforced epoxy composites." Composites Part B: Engineering. 116, pp. 186-199. https://doi.org/10.1016/j.compositesb.2017.02.015Butanol-acetone mixture blended with cottonseed biodiesel: spray characteristics evolution, combustion characteristics, engine performance and emission
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P., Yusaf, Talal and Al-lwayzy, Saddam. 2019. "Butanol-acetone mixture blended with cottonseed biodiesel: spray characteristics evolution, combustion characteristics, engine performance and emission." Proceedings of the Combustion Institute. 37 (4), pp. 4729-4739. https://doi.org/10.1016/j.proci.2018.08.035Experimental investigation of hydrated butanol-acetone (BA) and diesel blend as alternative fuel for CI engines
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P. and Yusaf, Talal. 2018. "Experimental investigation of hydrated butanol-acetone (BA) and diesel blend as alternative fuel for CI engines." 37th International Symposium on Combustion. Dublin, Ireland 29 Jul - 03 Aug 2018 Pittsburgh, PA, United States.Experimental and numerical investigation of spray characteristics of butanol-diesel blends
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P. and Yusaf, Talal. 2017. "Experimental and numerical investigation of spray characteristics of butanol-diesel blends." Masri, A. R., Cleary, M., Dunn, M., Kourmatzis, A., Hawkes, E., Kook, S. and Chan, Q. N. (ed.) 11th Asia-Pacific Conference on Combustion. Sydney, Australia 10 - 14 Dec 2017 Australia.Experimental study of spray characteristics, engine performance and emission levels of acetone-butanol-ethanol mixture-diesel blends in a diesel engine
Algayyim, Sattar Jabbar Murad, Wandel, Andrew, Yusaf, Talal, Hamawand, Ihsan and Al-lwayzy, Saddam. 2017. "Experimental study of spray characteristics, engine performance and emission levels of acetone-butanol-ethanol mixture-diesel blends in a diesel engine." Masri, A. R., Cleary, M., Dunn, M., Kourmatzis, A., Hawkes, E., Kook, S. and Chan, Q. N. (ed.) 11th Asia-Pacific Conference on Combustion. Sydney, Australia 10 - 14 Dec 2017 Australia.The effect of butanol-acetone mixture-cottonseed biodiesel blend on spray characteristics, engine performance and emissions in diesel engine
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P. and Yusaf, Talal. 2017. "The effect of butanol-acetone mixture-cottonseed biodiesel blend on spray characteristics, engine performance and emissions in diesel engine." Masri, A. R., Cleary, M., Dunn, M., Kourmatzis, A., Hawkes, E., Kook, S. and Chan, Q. N. (ed.) 11th Asia-Pacific Conference on Combustion. Sydney, Australia 10 - 14 Dec 2017 Australia.The impact of injector hole diameter on spray behaviour for butanol-diesel blends
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P. and Yusaf, Talal. 2018. "The impact of injector hole diameter on spray behaviour for butanol-diesel blends." Energies. 11 (5), pp. 1298-1310. https://doi.org/10.3390/en11051298Impact of butanol-acetone mixture as a fuel additive on diesel engine performance and emissions
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P., Yusaf, Talal, Al-Lwayzy, Saddam and Hamawand, Ihsan. 2018. "Impact of butanol-acetone mixture as a fuel additive on diesel engine performance and emissions." Fuel: the science and technology of fuel and energy. 227, pp. 118-126. https://doi.org/10.1016/j.fuel.2018.04.091Production and application of ABE as a biofuel
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P., Yusaf, Talal and Hamawand, Ihsan. 2018. "Production and application of ABE as a biofuel." Renewable and Sustainable Energy Reviews. 82, pp. 1195-1214. https://doi.org/10.1016/j.rser.2017.09.082A critical review on processes and energy profile of the Australian meat processing industry
Hamawand, Ihsan, Ghadouani, Anas, Bundschuh, Jochen, Hamawand, Sara, Al Juboori, Raed A., Chakrabarty, Sayan and Yusaf, Talal. 2017. "A critical review on processes and energy profile of the Australian meat processing industry." Energies. 10 (5). https://doi.org/10.3390/en10050731The impact of n-butanol and iso-butanol as components of butanol-acetone (BA) mixture-diesel blend on spray, combustion characteristics, engine performance and emission in direct injection diesel engine
Algayyim, Sattar Jabbar Murad, Wandel, Andrew P., Yusaf, Talal and Hamawand, Ihsan. 2017. "The impact of n-butanol and iso-butanol as components of butanol-acetone (BA) mixture-diesel blend on spray, combustion characteristics, engine performance and emission in direct injection diesel engine." Energy. 140, pp. 1074-1086. https://doi.org/10.1016/j.energy.2017.09.044Investigation of ethanol production potential from lignocellulosic material without enzymatic hydrolysis using the ultrasound technique
Kandasamy, Manoj, Hamawand, Ihsan, Bowtell, Leslie, Seneweera, Saman, Chakrabarty, Sayan, Yusaf, Talal, Shakoor, Zaidoon, Algayyim, Sattar and Eberhard, Friederike. 2017. "Investigation of ethanol production potential from lignocellulosic material without enzymatic hydrolysis using the ultrasound technique." Energies. 10 (1), pp. 62-73. https://doi.org/10.3390/en10010062Algae-biomass for fuel, electricity and agriculture
Bundschuh, Jochen, Yusaf, Talal, Maity, Jyoti Prakash, Nelson, Emily, Mamat, Rizalman and Mahlia, T. M. Indra. 2014. "Algae-biomass for fuel, electricity and agriculture ." Energy. 78, pp. 1-3. https://doi.org/10.1016/j.energy.2014.11.005Influence of chemical blends on palm oil methyl esters' cold flow properties and fuel characteristics
Ali, Obed M., Yusaf, Talal, Mamat, Rizalman, Abdullah, Nik R. and Abdullah, Abdul Adam. 2014. "Influence of chemical blends on palm oil methyl esters' cold flow properties and fuel characteristics." Energies. 7 (7), pp. 4364-4380. https://doi.org/10.3390/en7074364Sustainable energy and climate protection solutions in agriculture
Bundschuh, Jochen, Chen, Guangnan, Yusaf, Talal, Yan, Jinyue and Chen, Shulin. 2014. "Sustainable energy and climate protection solutions in agriculture ." Applied Energy. 114, pp. 735-736. https://doi.org/10.1016/j.apenergy.2013.11.037Optimization of biodiesel-diesel blended fuel properties and engine performance with ether additive using statistical analysis and response surface methods
Ali, Obed M., Mamat, Rizalman, Najafi, Gholamhassan, Yusaf, Talal and Ardebili, Seyed Mohammad Safieddin. 2015. "Optimization of biodiesel-diesel blended fuel properties and engine performance with ether additive using statistical analysis and response surface methods." Energies. 8 (12), pp. 14136-14150. https://doi.org/10.3390/en81212420TOPSIS multi-criteria decision modeling approach for biolubricant selection for two-stroke petrol engines
Soufi, Masoud Dehghani, Ghobadian, Barat, Najafi, Gholamhassan, Sabzimaleki, Mohammad Reza and Yusaf, Talal. 2015. "TOPSIS multi-criteria decision modeling approach for biolubricant selection for two-stroke petrol engines." Energies. 8 (12), pp. 13960-13970. https://doi.org/10.3390/en81212408Combustion of microalgae oil and ethanol blended with diesel fuel
Al-lwayzy, Saddam H. and Yusaf, Talal. 2015. "Combustion of microalgae oil and ethanol blended with diesel fuel." Energies. 8 (12), pp. 13985-13995. https://doi.org/10.3390/en81212409Glycerin, a biodiesel by-product with potentiality to produce hydrogen by steam gasification
Suero, Silvia Roman, Cano, Beatriz Ledesma, Alvarez-Murillo, Andres, Al-Kassir, Awf and Yusaf, Talal. 2015. "Glycerin, a biodiesel by-product with potentiality to produce hydrogen by steam gasification." Energies. 8 (11), pp. 12765-12775. https://doi.org/10.3390/en81112339SVM and ANFIS for prediction of performance and exhaust emissions of a SI engine with gasoline-ethanol blended fuels
Najafi, G., Ghobadian, B., Moosavian, A., Yusaf, T., Mamat, R., Kettner, M. and Azmi, W. H.. 2016. "SVM and ANFIS for prediction of performance and exhaust emissions of a SI engine with gasoline-ethanol blended fuels." Applied Thermal Engineering. 95, pp. 186-203. https://doi.org/10.1016/j.applthermaleng.2015.11.009Synthesis and optimization of Hevea brasiliensis and Ricinus communis as feedstock for biodiesel production: a comparative study
Silitonga, A. S., Masjuki, H. H., Ong, Hwai Chyuan, Kusumo, F., Yusaf, Talal and Mahlia, T. M. I.. 2016. "Synthesis and optimization of Hevea brasiliensis and Ricinus communis as feedstock for biodiesel production: a comparative study." Industrial Crops and Products. 85, pp. 274-286. https://doi.org/10.1016/j.indcrop.2016.03.017Impact of butanol-acetone mixture as an oxygenated fuel additive to diesel fuel on diesel engine performance and emissions
Algayyim, Sattar, Wandel, Andrew, Yusaf, Talal, Hamawand, Ihsan and Al-lwayzy, Saddam. 2016. "Impact of butanol-acetone mixture as an oxygenated fuel additive to diesel fuel on diesel engine performance and emissions." 36th International Symposium on Combustion. Seoul, Korea 31 Jul - 05 Aug 2016The experimental investigation of butanol-diesel blend on engine performance and emission levels in DI diesel engine
Algayyim, Sattar, Wandel, Andrew P., Yusaf, Talal, Hamawand, Ihsan and Al-lwayzy, Saddam. 2017. "The experimental investigation of butanol-diesel blend on engine performance and emission levels in DI diesel engine." 1st MoHESR and HCED Iraq Scholars Conference in Australasia 2017 (ISCA 2017). Melbourne, Australia 05 - 06 Dec 2017 Melbourne, Australia.SI: materials, design and tribology
Yousif, B. F.. 2013. "SI: materials, design and tribology." Materials and Design. 48. https://doi.org/10.1016/j.matdes.2013.01.009Design, fabrication and evaluation of gamma-type stirling engine to produce electricity from biomass for the micro-CHP system
Damirchi, Hojjat, Najafi, Gholam Hassan, Alizadehnia, Siamak, Ghobadian, Barat, Yusaf, Talal and Mamat, Rizalman. 2015. "Design, fabrication and evaluation of gamma-type stirling engine to produce electricity from biomass for the micro-CHP system." The 7th International Conference on Applied Energy - ICAE2015. Abu Dhabi, United Arab Emirates 28 - 31 Mar 2015 Netherlands. https://doi.org/10.1016/j.egypro.2015.07.240Energy conversion efficiency of pulsed ultrasound
Al-Juboori, Raed A., Yusaf, Talal and Bowtell, Leslie. 2015. "Energy conversion efficiency of pulsed ultrasound." The 7th International Conference on Applied Energy - ICAE2015. Abu Dhabi, United Arab Emirates 28 - 31 Mar 2015 Netherlands. Elsevier. https://doi.org/10.1016/j.egypro.2015.07.340The study of air fuel ratio for open furnace MILD combustion of biogas on bluff-body burner
Noor, M. M., Wandel, Andrew P. and Yusaf, T. F.. 2012. "The study of air fuel ratio for open furnace MILD combustion of biogas on bluff-body burner." 2012 Southern Regional Engineering Conference (SREC 2012). Toowoomba, Australia 01 Sep 2012 Canberra, Australia.Biofuel from microalgae: alternative, sustainable and renewable fuel
Najafi, Gholamhassan, Ghobadian, Barat and Yusaf, Talal F.. 2011. "Biofuel from microalgae: alternative, sustainable and renewable fuel ." 10th International Conference on Sustainable Energy Technologies (SET 2011). Istanbul, Turkey 04 - 07 Sep 2011Evaluation of alternative energy sources for cotton production in Australia
Chen, Guangnan, Sandell, Gary, Yusaf, Talal and Baillie, Craig. 2013. "Evaluation of alternative energy sources for cotton production in Australia." SEAg 2013: Innovative Agricultural Technologies for a Sustainable Future. Barton, Australia 22 - 25 Sep 2013 Barton, ACT, Australia.Corrosion effects of CNT-nanofluids on different metals
Ismail, A. F., Anuar, A., Rashmi, W. and Yusaf, T.. 2014. "Corrosion effects of CNT-nanofluids on different metals." 3rd International Conference on Advanced Materials and Information Technology Processing (AMITP 2013). Los Angeles, United States 01 - 02 Dec 2013 Southampton, United Kingdom. https://doi.org/10.2495/AMITP20130171Wear and frictional behaviour of metals
Alotaibi, J. G., Yousif, B. F. and Yusaf, T. F.. 2014. "Wear and frictional behaviour of metals." Kida, Katsuyuki (ed.) 3rd International Conference on Advanced Materials and Engineering Materials (ICAMEM 2013). Singapore 14 - 15 Dec 2013 Zurich, Switzerland. https://doi.org/10.4028/www.scientific.net/AMR.893.430The development of MILD combustion open burner experimental setup
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "The development of MILD combustion open burner experimental setup." Ishak, Mahadzir and Rahman, Md. Mustafizur (ed.) 2nd International Conference of Mechanical Engineering Research (ICMER 2013). Pahang, Malaysia 01 - 03 Jul 2013 Pahang, Malaysia.Detail guide for CFD on the simulation of biogas combustion in bluff-body mild burner
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "Detail guide for CFD on the simulation of biogas combustion in bluff-body mild burner." Ishak, Mahadzir and Rahman, Md. Mustafizur (ed.) 2nd International Conference of Mechanical Engineering Research (ICMER 2013). Pahang, Malaysia 01 - 03 Jul 2013 Pahang, Malaysia.Mild combustion: the future for lean and clean combustion
Yusaf, Talal, Noor, M. M. and Wandel, Andrew P.. 2013. "Mild combustion: the future for lean and clean combustion." Ishak, Mahadzir and Rahman, Md. Mustafizur (ed.) 2nd International Conference of Mechanical Engineering Research (ICMER 2013). Pahang, Malaysia 01 - 03 Jul 2013 Pahang, Malaysia.Alternative energy sources fro cotton production
Baillie, Craig, Sandell, Gary, Chen, Guangnan and Yusaf, Talal. 2012. "Alternative energy sources fro cotton production." 16th Australian Cotton Conference (ACC 2012): Growing Better all the Time. Gold Coast, Australia 14 - 16 Aug 2012 Gold Coast, Australia.Investigation of the effect of additives to natural gas on heavy-duty SI engine combustion characteristics
Gharehghani, A., Hosseini, R. and Yusaf, T.. 2013. "Investigation of the effect of additives to natural gas on heavy-duty SI engine combustion characteristics." Journal of Mechanical Engineering and Sciences. 5, pp. 677-687. https://doi.org/10.15282/jmes.5.2013.14.0065Characterization of a diesel engine operating with a small proportion of methanol as a fuel additive in biodiesel blend
Mat Yasin, M. H., Yusaf, Talal, Mamat, R. and Yusop, A. Fitri. 2014. "Characterization of a diesel engine operating with a small proportion of methanol as a fuel additive in biodiesel blend." Applied Energy. 114, pp. 865-873. https://doi.org/10.1016/j.apenergy.2013.06.012An investigation on tensile, compression and flexural properties of natural fibre reinforced polyester composites
Yousif, B. F., Jye, W. K. and El-Tayeb, N. S. M.. 2007. "An investigation on tensile, compression and flexural properties of natural fibre reinforced polyester composites." 2007 ASME International Mechanical Engineering Congress and Exposition (IMECE 2007). Seattle, United States of America 11 - 15 Nov 2007 Boston, Massachusetts, USA.Transesterification of Nannochloropsis oculata microalga's oil to biodiesel using calcium methoxide catalyst
Teo, Siow Hwa, Islam, Aminul, Yusaf, Talal and Taufiq-Yap, Yun Hin. 2014. "Transesterification of Nannochloropsis oculata microalga's oil to biodiesel using calcium methoxide catalyst." Energy. 78, pp. 63-71. https://doi.org/10.1016/j.energy.2014.07.045Investigation on interfacial adhesion of date palm/epoxy using fragmentation technique
Shalwan, A. and Yousif, B. F.. 2014. "Investigation on interfacial adhesion of date palm/epoxy using fragmentation technique." Materials and Design. 53, pp. 928-937. https://doi.org/10.1016/j.matdes.2013.07.083Experimental investigation on the interfacial adhesion of date palm fibres with epoxy matrix
Alsaeed, T., Alajmi, A., Yousif, B. F., Ku, H. and Lau, Alan Kin-tak. 2012. "Experimental investigation on the interfacial adhesion of date palm fibres with epoxy matrix." Heslehurst, Rikard Benton and Byrne, Ann (ed.) Composites Australia and the CRC for Advanced Composite Structures Conference 2012: Diversity in Composites. Leura, Australia 15 - 16 Mar 2012 Melbourne, Australia.Numerical and experimental study of microorganism disruption using shock treatment
Yusaf, Talal and Al Juboori, Raed A.. 2015. "Numerical and experimental study of microorganism disruption using shock treatment." Journal of Biotechnology. 208 (Supplement), pp. S15-S15. https://doi.org/10.1016/j.jbiotec.2015.06.035Investigating natural organic carbon removal and structural alteration induced by pulsed ultrasound
Al-Juboori, Raed A., Yusaf, Talal, Aravinthan, Vasantha and Bowtell, Leslie. 2016. "Investigating natural organic carbon removal and structural alteration induced by pulsed ultrasound." Science of the Total Environment. 541, pp. 1019-1030. https://doi.org/10.1016/j.scitotenv.2015.09.143Insights into the scalability of magnetostrictive ultrasound technology for water treatment applications
Al-Juboori, Raed A., Bowtell, Leslie A., Yusaf, Talal and Aravinthan, Vasantha. 2016. "Insights into the scalability of magnetostrictive ultrasound technology for water treatment applications." Ultrasonics Sonochemistry. 28, pp. 357-366. https://doi.org/10.1016/j.ultsonch.2015.08.013Determination of drying characteristics of biomass residues to be used as a renewable fuel
Al Kassir, Awf, Yusaf, Talal, Al Karany, Raul Kassir and Hamawand, Ihsan. 2015. "Determination of drying characteristics of biomass residues to be used as a renewable fuel." Journal of Biotechnology. 208 (Supplement), pp. S15-S15. https://doi.org/10.1016/j.jbiotec.2015.06.034Single-zone zero-dimensional model study for diesel-fuelled homogeneous charge compression ignition (HCCI) engines using Cantera
Hairuddin, A. Aziz, Yusaf, Talal and Wandel, Andrew P.. 2016. "Single-zone zero-dimensional model study for diesel-fuelled homogeneous charge compression ignition (HCCI) engines using Cantera." International Journal of Automotive and Mechanical Engineering. 13 (2), pp. 3309-3328. https://doi.org/10.15282/ijame.13.2.2016.3.0275Diesel engine performance and exhaust gas emissions using microalgae Chlorella protothecoides biodiesel
Al-lwayzy, Saddam H. and Yusaf, Talal. 2017. "Diesel engine performance and exhaust gas emissions using microalgae Chlorella protothecoides biodiesel." Renewable Energy. 101, pp. 690-701. https://doi.org/10.1016/j.renene.2016.09.035Bioenergy from cotton industry wastes: a review and potential
Hamawand, Ihsan, Sandell, Gary, Pittaway, Pam, Chakrabarty, Sayan, Yusaf, Talal, Chen, Guangnan, Seneweera, Saman, Al-Lwayzy, Saddam, Bennett, John and Hopf, Joshua. 2016. "Bioenergy from cotton industry wastes: a review and potential." Renewable and Sustainable Energy Reviews. 66, pp. 435-448. https://doi.org/10.1016/j.rser.2016.08.033An assessment of direct on-farm energy use for high value grain crops grown under different farming practices in Australia
Maraseni, Tek, Chen, Guangnan, Banhazi, Thomas, Bundschuh, Jochen and Yusaf, Talal. 2015. "An assessment of direct on-farm energy use for high value grain crops grown under different farming practices in Australia." Energies. 8 (11), pp. 13033-13046. https://doi.org/10.3390/en81112353Tracking ultrasonically structural changes of natural aquatic organic carbon: chemical fractionation and spectroscopic approaches
Al-Juboori, Raed A., Yusaf, Talal, Aravinthan, Vasantha and Bowtell, Leslie. 2016. "Tracking ultrasonically structural changes of natural aquatic organic carbon: chemical fractionation and spectroscopic approaches." Chemosphere. 145, pp. 231-248. https://doi.org/10.1016/j.chemosphere.2015.11.079Natural fibers and their characterization
Azwa, Z. N., Yousif, B. F., Manalo, A. C. and Karunasena, W.. 2016. "Natural fibers and their characterization." Campilho, R. D. S. G. (ed.) Natural fiber composites. Boca Raton, FL, United States. CRC Press. pp. 35-64Biolubricants and the potential of waste cooking oil
Alotaibi, J. G. and Yousif, B. F.. 2016. "Biolubricants and the potential of waste cooking oil." Davim, J. Paulo (ed.) Ecotribology, research developments. Switzerland. Springer. pp. 125-143Two-body abrasion of bamboo fibre/epoxy composites
Oun, A. and Yousif, B. F.. 2016. "Two-body abrasion of bamboo fibre/epoxy composites." Davim, J. Paulo (ed.) Ecotribology, research developments. Switzerland. Springer. pp. 145-172Optimization of performance and exhaust emission parameters of a SI (spark ignition) engine with gasoline-ethanol blended fuels using response surface methodology
Najafi, Gholamhassan, Ghobadian, Barat, Yusaf, Talal, Ardebili, Seyed Mohammad Safieddin and Mamat, Rizalman. 2015. "Optimization of performance and exhaust emission parameters of a SI (spark ignition) engine with gasoline-ethanol blended fuels using response surface methodology." Energy. 90 (2), pp. 1815-1829. https://doi.org/10.1016/j.energy.2015.07.004Solar energy in Iran: current state and outlook
Najafi, G., Ghobadian, B., Mamat, R., Yusaf, T. and Azmi, W. H.. 2015. "Solar energy in Iran: current state and outlook." Renewable and Sustainable Energy Reviews. 49, pp. 931-942. https://doi.org/10.1016/j.rser.2015.04.056An experimental study on reactivity controlled compression ignition engine fueled with biodiesel/natural gas
Gharehghani, Ayatallah, Hosseini, Reza, Mirsalim, Mostafa, Jazayeri, S. Ali and Yusaf, Talal. 2015. "An experimental study on reactivity controlled compression ignition engine fueled with biodiesel/natural gas." Energy. 89, pp. 558-567. https://doi.org/10.1016/j.energy.2015.06.014A comparative study on the first and second law analysis and performance characteristics of a spark ignition engine using either natural gas or gasoline
Gharehghani, A., Hosseini, R., Mirsalim, M. and Yusaf, Talal F.. 2015. "A comparative study on the first and second law analysis and performance characteristics of a spark ignition engine using either natural gas or gasoline." Fuel: the science and technology of fuel and energy. 158, pp. 488-493. https://doi.org/10.1016/j.fuel.2015.05.067Influence of metal coating on sorghum milling process subjected to three body abrasion
Al-Sandooq, Jaafar Mahdi, Yousif, Belal and Jensen, T. A.. 2015. "Influence of metal coating on sorghum milling process subjected to three body abrasion." International Journal of Precision Technology. 5 (1), pp. 27-42. https://doi.org/10.1504/IJPTECH.2015.069972Editor's introduction to special theme issue [of International Journal of Precision Technology]: Precision engineering and tribology
Yousif, Belal. 2015. "Editor's introduction to special theme issue [of International Journal of Precision Technology]: Precision engineering and tribology." International Journal of Precision Technology. 5 (1).Exploring the correlations between common UV measurements and chemical fractionation for natural waters
Al-Juboori, Raed A., Yusaf, Talal and Pittaway, Pamela A.. 2016. "Exploring the correlations between common UV measurements and chemical fractionation for natural waters ." Desalination and Water Treatment. 57 (35), pp. 16324-16335. https://doi.org/10.1080/19443994.2015.1079805A computational study of operating range extension in a natural gas SI engine with the use of hydrogen
Gharehghani, A., Hosseini, R., Mirsalim, M. and Yusaf, Talal F.. 2015. "A computational study of operating range extension in a natural gas SI engine with the use of hydrogen." International Journal of Hydrogen Energy. 40 (17), pp. 5966-5975. https://doi.org/10.1016/j.ijhydene.2015.03.015A comparison of household carbon emission patterns of urban and rural China over the 17 year period (1995–2011)
Qu, Jiansheng, Maraseni, Tek, Liu, Lina, Zhang, Zhiqiang and Yusaf, Talal. 2015. "A comparison of household carbon emission patterns of urban and rural China over the 17 year period (1995–2011)." Energies. 8 (9), pp. 10537-10557. https://doi.org/10.3390/en80910537Impact of pulsed ultrasound on bacteria reduction of natural waters
Al-Juboori, Raed A., Aravinthan, Vasantha and Yusaf, Talal. 2015. "Impact of pulsed ultrasound on bacteria reduction of natural waters." Ultrasonics Sonochemistry. 27, pp. 137-147. https://doi.org/10.1016/j.ultsonch.2015.05.007The influence of straight vegetable oil fatty acid composition on compression ignition combustion and emissions
Hellier, Paul, Ladommatos, Nicos and Yusaf, Talal. 2015. "The influence of straight vegetable oil fatty acid composition on compression ignition combustion and emissions." Fuel: the science and technology of fuel and energy. 143, pp. 131-143. https://doi.org/10.1016/j.fuel.2014.11.021Assessing the application and downstream effects of pulsed mode ultrasound as a pre-treatment for alum coagulation
Al-Juboori, Raed A., Aravinthan, Vasantha, Yusaf, Talal and Bowtell, Leslie. 2016. "Assessing the application and downstream effects of pulsed mode ultrasound as a pre-treatment for alum coagulation." Ultrasonics Sonochemistry. 31, pp. 7-19. https://doi.org/10.1016/j.ultsonch.2015.11.028Evaluating the impact of operating parameters on biocidal effects of pulsed ultrasound in natural water disinfection
Al Juboori, Raed A., Yusaf, Talal and Aravinthan, Vasantha. 2015. "Evaluating the impact of operating parameters on biocidal effects of pulsed ultrasound in natural water disinfection." Journal of Biotechnology. 208 (Supplement), pp. S17-S18. https://doi.org/10.1016/j.jbiotec.2015.06.042Brass, aluminium, and mild steel sliding against stainless steel under dry conditions
Alotaibi, J. G., Yousif, B. F. and Yusaf, T. F.. 2015. "Brass, aluminium, and mild steel sliding against stainless steel under dry conditions." International Journal of Precision Technology. 5 (2), pp. 85-96.Multimedia resources in engineering
Yousif, B. F., Basson, Marita and Hobohm, Carola. 2014. "Multimedia resources in engineering." Davim, J. Paulo (ed.) Modern mechanical engineering: research, development and education. Heidelberg, Germany. Springer. pp. 449-461Wear behaviour and mechanism of different metals sliding against stainless steel counterface
Alotaibi, J. G., Yousif, B. F. and Yusaf, T. F.. 2014. "Wear behaviour and mechanism of different metals sliding against stainless steel counterface." Proceedings of the Institution of Mechanical Engineers Part J: Journal of Engineering Tribology. 228 (6), pp. 692-704. https://doi.org/10.1177/1350650114527072Effect of SiC addition on mechanical and wear characteristics of WC-32(W-Ti)C-6Co cemented carbides
Albdiry, M. T. and Yousif, B. F.. 2014. "Effect of SiC addition on mechanical and wear characteristics of WC-32(W-Ti)C-6Co cemented carbides." International Journal of Precision Technology. 4 (1/2), pp. 110-121. https://doi.org/10.1504/IJPTECH.2014.060611Evaluating the effect of heat transfer on cell disruption in ultrasound processes
Yusaf, Talal. 2015. "Evaluating the effect of heat transfer on cell disruption in ultrasound processes." Annals of Microbiology. 65 (3), pp. 1447-1456. https://doi.org/10.1007/s13213-014-0983-zRole of silanized halloysite nanotubes on structural, mechanical properties and fracture toughness of thermoset nanocomposites
Albdiry, M. T. and Yousif, B. F.. 2014. "Role of silanized halloysite nanotubes on structural, mechanical properties and fracture toughness of thermoset nanocomposites." Materials and Design. 57, pp. 279-288. https://doi.org/10.1016/j.matdes.2013.12.017Engine performance and emissions using Jatropha curcas, Ceiba pentandra and Calophyllum inophyllum biodiesel in a CI diesel engine
Ong, Hwai Chyuan, Masjuki, H. H., Mahlia, T. M. I., Silitonga, A. S., Chong, W. T. and Yusaf, Talal. 2014. "Engine performance and emissions using Jatropha curcas, Ceiba pentandra and Calophyllum inophyllum biodiesel in a CI diesel engine." Energy. 69, pp. 427-445. https://doi.org/10.1016/j.energy.2014.03.035Growing algae using water from coal seam gas industry and harvesting using an innovative technique: a review and a potential
Hamawand, Ihsan, Yusaf, Talal and Hamawand, Sara. 2014. "Growing algae using water from coal seam gas industry and harvesting using an innovative technique: a review and a potential." Fuel: the science and technology of fuel and energy. 117 (Part A), pp. 422-430. https://doi.org/10.1016/j.fuel.2013.09.040An introduction to a homogeneous charge compression ignition engine
Hairuddin, A. A., Wandel, A. P. and Yusaf, T.. 2014. "An introduction to a homogeneous charge compression ignition engine." Journal of Mechanical Engineering and Sciences. 7, pp. 1042-1052. https://doi.org/10.15282/jmes.7.2014.3.0101Investigating the feasibility and the optimal location of pulsed ultrasound in surface water treatment schemes
Al-Juboori, Raed A., Yusaf, Talal, Aravinthan, Vasantha, Pittaway, Pamela A. and Bowtell, Leslie. 2016. "Investigating the feasibility and the optimal location of pulsed ultrasound in surface water treatment schemes." Desalination and Water Treatment. 57 (11), pp. 4769-4787. https://doi.org/10.1080/19443994.2014.996771Investigating corrosion effects and heat transfer enhancement in smaller size radiators using CNT-nanofluids
Rashmi, W., Ismail, A. F., Khalid, M., Anuar, A. and Yusaf, T.. 2014. "Investigating corrosion effects and heat transfer enhancement in smaller size radiators using CNT-nanofluids." Journal of Materials Science. 49 (13), pp. 4544-4551. https://doi.org/10.1007/s10853-014-8154-yStatistical diagnosis of the best weibull methods for wind power assessment for agricultural applications
Azad, Abul Kalam, Rasul, Mohammad Golam and Yusaf, Talal. 2014. "Statistical diagnosis of the best weibull methods for wind power assessment for agricultural applications." Energies. 7 (5), pp. 3056-3085. https://doi.org/10.3390/en7053056Influence of date palm fibre and graphite filler on mechanical and wear characteristics of epoxy composites
Shalwan, A. and Yousif, B. F.. 2014. "Influence of date palm fibre and graphite filler on mechanical and wear characteristics of epoxy composites." Materials and Design. 59, pp. 264-273. https://doi.org/10.1016/j.matdes.2014.02.066A review of hydrogen and natural gas addition in diesel HCCI engines
Hairuddin, A. Aziz, Yusaf, Talal and Wandel, Andrew P.. 2014. "A review of hydrogen and natural gas addition in diesel HCCI engines." Renewable and Sustainable Energy Reviews. 32, pp. 739-761. https://doi.org/10.1016/j.rser.2014.01.018Energy characterisation of ultrasonic systems for industrial processes
Al-Juboori, Raed A., Yusaf, Talal, Bowtell, Leslie and Aravinthan, Vasantha. 2015. "Energy characterisation of ultrasonic systems for industrial processes." Ultrasonics. 57, pp. 18-30. https://doi.org/10.1016/j.ultras.2014.10.003Coals seam gas (CSG) in agriculture - a review: technical and market analysis for Australia
Yusaf, Talal, Hamawand, Ihsan, Schmidt, Erik, Binnie, James, Rees, Steven and Chakrabarty, Sayan. 2014. "Coals seam gas (CSG) in agriculture - a review: technical and market analysis for Australia ." Sustainable Energy Technologies and Assessments. 8, pp. 149-158. https://doi.org/10.1016/j.seta.2014.08.005Kenaf fibers for tribo-thermoplastic composites
Singh, Narish, Rilling, Dirk and Yousif, B. F.. 2010. "Kenaf fibers for tribo-thermoplastic composites." Ghia, Urmila (ed.) 2009 ASME International Mechanical Engineering Congress and Exposition (IMECE 2009). Florida, United States of America 13 - 19 Nov 2009 United States. https://doi.org/10.1115/IMECE2009-10167New technique measuring film thickness for tribological machines
Al-Haddad, A. A., Salih, Nbhan D., Wen, Chin Chee, Yusaf, T. F. and Yousif, B. F.. 2010. "New technique measuring film thickness for tribological machines." 2009 ASME International Mechanical Engineering Congress and Exposition (IMECE 2009). Florida, United States of America 13 - 19 Nov 2009 United States. https://doi.org/10.1115/IMECE2009-10160Air fuel ratio study for mixture of biogas and hydrogen on mild combustion
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2014. "Air fuel ratio study for mixture of biogas and hydrogen on mild combustion." International Journal of Automotive and Mechanical Engineering. 10 (1), pp. 2144-2154. https://doi.org/10.15282/ijame.9.2013.29.0180Effect of air-fuel ratio on temperature distribution and pollutants for biogas MILD combustion
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2014. "Effect of air-fuel ratio on temperature distribution and pollutants for biogas MILD combustion." International Journal of Automotive and Mechanical Engineering. 10 (1), pp. 1980-1992. https://doi.org/10.15282/ijame.10.2014.15.0166The simulation of biogas combustion in a MILD burner
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2014. "The simulation of biogas combustion in a MILD burner." Journal of Mechanical Engineering and Sciences. 6 (1), pp. 995-1013.Design of film thickness instrument for fibre polymer composites tribological experiments
Yousif, B. F., Al-Haddad, A., Alotaibi, J. GH. and Yusaf, T. F.. 2014. "Design of film thickness instrument for fibre polymer composites tribological experiments." Journal of Engineering Science and Technology. 9 (2), pp. 154-166.High-stress three-body abrasive wear of treated and untreated oil palm fibre-reinforced polyester composites
Yousif, B. F. and El-Tayeb, N. S. M.. 2008. "High-stress three-body abrasive wear of treated and untreated oil palm fibre-reinforced polyester composites." Proceedings of the Institution of Mechanical Engineers Part J: Journal of Engineering Tribology. 222 (5), pp. 637-646. https://doi.org/10.1243/13506501JET412On the effect of roller materials on the power window mechanism from a tribological perspective
Chee, S. B., Shalabi, Ammar Al, Chin, C. W. and Yousif, B. F.. 2009. "On the effect of roller materials on the power window mechanism from a tribological perspective." 2008 ASME International Mechanical Engineering Congress and Exposition (IMECE 2008). Boston, United States of America 31 Oct - 06 Nov 2008 New York, NY. United States. https://doi.org/10.1115/IMECE2008-66112On the mechanical properties of a treated betelnut fibre-reinforced polyester composite
Yousif, B. F. and Nirmal, U.. 2010. "On the mechanical properties of a treated betelnut fibre-reinforced polyester composite." Proceedings of the Institution of Mechanical Engineers Part C: Journal of Mechanical Engineering Science. 224 (9), pp. 1805-1814. https://doi.org/10.1243/09544062JMES1943Framework for orienting engineering undergraduate final year projects towards new product innovation process
Al-Shalabi, Ammar, Chee, S. B., Singh, Narish and Yousif, B. F.. 2008. "Framework for orienting engineering undergraduate final year projects towards new product innovation process." Soliman, Khalid S. (ed.) 10th Conference on Innovation and Knowledge Management in Business Globalization (IBIMA 2008). Kuala Lumpur, Malaysia 30 Jun - 01 Jul 2008 Norristown, PA. United States.The effect of treatment on tribo-performance of CFRP composites
Yousif, Belal F., Leong, Ong B., Ong, Low K. and Jye, Wong K.. 2009. "The effect of treatment on tribo-performance of CFRP composites." Recent Patents on Materials Science. 2 (1), pp. 67-74. https://doi.org/10.2174/1874464810902010067Wear and friction characteristics of CGRP composite under wet contact condition using two different test techniques
Yousif, B. F. and El-Tayeb, N. S. M.. 2008. "Wear and friction characteristics of CGRP composite under wet contact condition using two different test techniques." Wear. 265 (5-6), pp. 856-864. https://doi.org/10.1016/j.wear.2008.01.016Machinability of glass/date palm fibre epoxy composites
Alsaeed, T. and Yousif, B. F.. 2014. "Machinability of glass/date palm fibre epoxy composites." International Journal of Machining and Machinability of Materials. 16 (2), pp. 129-150. https://doi.org/10.1504/IJMMM.2014.064685An experimental investigation of the effective parameters on wet washing of biodiesel purification
Abbaszadeh, A., Ghobadian, B., Najafi, G. and Yusaf, T.. 2014. "An experimental investigation of the effective parameters on wet washing of biodiesel purification." International Journal of Automotive and Mechanical Engineering. 9 (1), pp. 1525-1537. https://doi.org/10.15282/ijame.9.2013.4.0126Smaller radiator with enhanced heat transfer using CNT-nanofluids
Ismail, A. F., Abd-Halim, B. A., Rashmi, W. and Yusaf, T.. 2014. "Smaller radiator with enhanced heat transfer using CNT-nanofluids ." Yang, G. (ed.) International Conference on Future Energy, Environment, and Materials (FEEM 2013). Hong Kong, China 24 - 25 Dec 2013 Southampton, United Kingdom. https://doi.org/10.2495/FEEM20130221Chlorella protothecoides microalgae as an alternative fuel for tractor diesel engines
Al-lwayzy, Saddam H. and Yusaf, Talal. 2013. "Chlorella protothecoides microalgae as an alternative fuel for tractor diesel engines." Energies. 6 (2), pp. 766-783. https://doi.org/10.3390/en6020766Correlation between frictional force, interface temperature and specific wear rate of fibre polymer composites
Arhaim, Y. H, Shalwan, A. and Yousif, B. F.. 2013. "Correlation between frictional force, interface temperature and specific wear rate of fibre polymer composites." Advanced Materials Research. 685 (685), pp. 45-49. https://doi.org/10.4028/www.scientific.net/AMR.685.45In state of art: mechanical and tribological behaviour of polymeric composites based on natural fibres
Shalwan, A. and Yousif, B. F.. 2013. "In state of art: mechanical and tribological behaviour of polymeric composites based on natural fibres." Materials and Design. 48, pp. 14-24. https://doi.org/10.1016/j.matdes.2012.07.014Coal seam gas and associated water: a review paper
Hamawand, Ihsan, Yusaf, Talal and Hamawand, Sara. 2013. "Coal seam gas and associated water: a review paper." Renewable and Sustainable Energy Reviews. 22, pp. 550-560. https://doi.org/10.1016/j.rser.2013.02.030Study and modelling drying of banana slices under superheated steam
Hamawand, Ihsan, Yusaf, Talal and Bennett, John. 2014. "Study and modelling drying of banana slices under superheated steam." Asia Pacific Journal of Chemical Engineering. 9 (4), pp. 591-603. https://doi.org/10.1002/apj.1788Biofuels from the fresh water microalgae Chlorella vulgaris (FWM-CV) for diesel engines
Al-lwayzy, Saddam H., Yusaf, Talal and Al-Juboori, Raed A.. 2014. "Biofuels from the fresh water microalgae Chlorella vulgaris (FWM-CV) for diesel engines." Energies. 7 (3), pp. 1829-1851. https://doi.org/10.3390/en7031829Fracture toughness and toughening mechanisms of unsaturated polyester-based clay nanocomposites
Albdiry, Mushtaq T., Yousif, Belal F. and Ku, Harry. 2013. "Fracture toughness and toughening mechanisms of unsaturated polyester-based clay nanocomposites." 13th International Conference on Fracture (ICF 2013). Beijing, China 16 - 21 Jun 2013 Anhui, China.Assessing a new approach to covered anaerobic pond design in the treatment of abattoir wastewater
McCabe, B. K., Harris, P., Baillie, C., Pittaway, P. and Yusaf, T.. 2013. "Assessing a new approach to covered anaerobic pond design in the treatment of abattoir wastewater." Australian Journal of Multi-Disciplinary Engineering. 10 (1), pp. 81-93. https://doi.org/10.7158/N12-AE07.2013.10.1.MILD combustion: the future for lean and clean combustion technology
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2014. "MILD combustion: the future for lean and clean combustion technology." International Review of Mechanical Engineering. 8 (1), pp. 251-257.Design and development of mild combustion burner
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "Design and development of mild combustion burner." Journal of Mechanical Engineering and Sciences. 5, pp. 662-676. https://doi.org/10.15282/jmes.5.2013.13.0064A review on the degradability of polymeric composites based on natural fibres
Azwa, Z. N., Yousif, B. F., Manalo, A. C. and Karunasena, W.. 2013. "A review on the degradability of polymeric composites based on natural fibres." Materials and Design. 47, pp. 424-442. https://doi.org/10.1016/j.matdes.2012.11.025Effect of different heat transfer models on a diesel homogeneous charge compression ignition engine
Hairuddin, Abdul Aziz, Yusaf, Talal and Wandel, Andrew. 2013. "Effect of different heat transfer models on a diesel homogeneous charge compression ignition engine." International Journal of Automotive and Mechanical Engineering. 8 (1), pp. 1292-1304.Implementation of CMC in a 0-D single-zone model of a diesel HCCI engine
Hairuddin, A. Aziz, Yusaf, Talal and Wandel, Andrew P.. 2013. "Implementation of CMC in a 0-D single-zone model of a diesel HCCI engine." Zhu, Mingming, Yu, Yun, Vuthaluru, Hari, Zhang, Zhezi and Zhang, Dongke (ed.) 7th Australian Combustion Symposium (ACS 2013). Perth, Australia 06 - 08 Nov 2013 Sydney, Australia.Performance analysis of journal bearings using ultrasonic reflection
Kasolang, S., Ahmed, Diyar I., Dwyer-Joyce, R. S. and Yousif, B. F.. 2013. "Performance analysis of journal bearings using ultrasonic reflection." Tribology International. 64, pp. 78-84. https://doi.org/10.1016/j.triboint.2013.02.012Experimental study of microorganism disruption using shear stress
Yusaf, Talal. 2013. "Experimental study of microorganism disruption using shear stress." Biochemical Engineering Journal. 79, pp. 7-14. https://doi.org/10.1016/j.bej.2013.07.001The effect of methanol-diesel blended ratio on CI engine performance
Yusaf, T., Hamawand, I., Baker, P. and Najafi, G.. 2013. "The effect of methanol-diesel blended ratio on CI engine performance." International Journal of Automotive and Mechanical Engineering. 8 (1), pp. 1385-1395. https://doi.org/10.15282/ijame.8.2013.26.0114Effect of compressed natural gas mixing on the engine performance and emissions
Yusaf, T., Baker, P., Hamawand, I. and Noor, M. M.. 2013. "Effect of compressed natural gas mixing on the engine performance and emissions." International Journal of Automotive and Mechanical Engineering. 8 (1), pp. 1416-1429.Analysis of recirculation zone and ignition position of non-premixed bluff-body for biogas mild combustion
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "Analysis of recirculation zone and ignition position of non-premixed bluff-body for biogas mild combustion." International Journal of Automotive and Mechanical Engineering. 8 (1), pp. 1176-1186.The analysis of recirculation zone and ignition position of non-premixed bluff-body for biogas mild combustion
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "The analysis of recirculation zone and ignition position of non-premixed bluff-body for biogas mild combustion." Ishak, Mahadzir and Rahman, Md. Mustafizur (ed.) 2nd International Conference of Mechanical Engineering Research (ICMER 2013). Pahang, Malaysia 01 - 03 Jul 2013 Pahang, Malaysia.Sustainable composites
Yousif, Belal F., Islam, Md Mainul and Salit, Mohd Sapuan. 2013. "Sustainable composites." Advances in Materials Science and Engineering. https://doi.org/10.1155/2013/142718Particles motion in a cascading rotary drum dryer
Hamawand, Ihsan and Yusaf, Talal. 2014. "Particles motion in a cascading rotary drum dryer." Canadian Journal of Chemical Engineering. 92 (4), pp. 648-662. https://doi.org/10.1002/cjce.21845Impact fracture behaviour of silane-treated halloysite nanotubes-reinforced unsaturated polyester
Albdiry, M. T., Ku, H. and Yousif, B. F.. 2013. "Impact fracture behaviour of silane-treated halloysite nanotubes-reinforced unsaturated polyester." Engineering Failure Analysis. 35, pp. 718-725. https://doi.org/10.1016/j.engfailanal.2013.06.027Experimental investigation of thermal balance of a turbocharged SI engine operating on natural gas
Gharehghani, A., Koochak, M., Mirsalim, M. and Yusaf, Talal. 2013. "Experimental investigation of thermal balance of a turbocharged SI engine operating on natural gas." Applied Thermal Engineering. 60 (1-2), pp. 200-207. https://doi.org/10.1016/j.applthermaleng.2013.06.029Experimental investigation of the tractor engine performance using diesohol fuel
Shadidi, Behdad, Yusaf, Talal, Alizadeh, Hossein Haji Agha and Ghobadian, Barat. 2014. "Experimental investigation of the tractor engine performance using diesohol fuel." Applied Energy. 114, pp. 874-879. https://doi.org/10.1016/j.apenergy.2013.06.011Characteristics of kenaf fibre/epoxy composites subjected to thermal degradation
Azwa, Z. N. and Yousif, B. F.. 2013. "Characteristics of kenaf fibre/epoxy composites subjected to thermal degradation." Polymer Degradation and Stability. 98 (12), pp. 2752-2759. https://doi.org/10.1016/j.polymdegradstab.2013.10.008Nutrient removal of nursery and municipal wastewater using Chlorella vulgaris microalgae for lipid extraction
Aravinthan, Vasantha, Story, Nadine and Yusaf, Talal. 2014. "Nutrient removal of nursery and municipal wastewater using Chlorella vulgaris microalgae for lipid extraction." Desalination and Water Treatment. 52 (4-6), pp. 727-736. https://doi.org/10.1080/19443994.2013.826325Recycling of waste engine oils using a new washing agent
Hamawand, Ihsan, Yusaf, Talal and Rafat, Sardasht. 2013. "Recycling of waste engine oils using a new washing agent." Energies. 6 (2), pp. 1023-1049. https://doi.org/10.3390/en6021023Production of biodiesel from Sterculia foetida and its process optimization
Silitonga, A. S., Ong, H. C., Masjuki, H. H., Mahlia, T. M. I., Chong, W. T. and Yusaf, Talal F.. 2013. "Production of biodiesel from Sterculia foetida and its process optimization ." Fuel: the science and technology of fuel and energy. 111, pp. 478-484. https://doi.org/10.1016/j.fuel.2013.03.051Numerical study of oxygen dilution and temperature distribution of biogas combustion in Bluff-body MILD burner
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "Numerical study of oxygen dilution and temperature distribution of biogas combustion in Bluff-body MILD burner." Masri, Assaad (ed.) 7th Australian Combustion Symposium (ACS 2013). Perth, Australia 06 - 08 Nov 2013 Perth, Australia.A case study for biogas generation from covered anaerobic ponds treating abattoir wastewater: investigation of pond performance and potential biogas production
McCabe, Bernadette K., Hamawand, Ihsan, Harris, Peter, Baillie, Craig and Yusaf, Talal. 2014. "A case study for biogas generation from covered anaerobic ponds treating abattoir wastewater: investigation of pond performance and potential biogas production." Applied Energy. 114, pp. 798-808. https://doi.org/10.1016/j.apenergy.2013.10.020Alternative methods of microorganism disruption for agricultural applications
Yusaf, Talal and Al-Juboori, Raed A.. 2014. "Alternative methods of microorganism disruption for agricultural applications ." Applied Energy. 114, pp. 909-923. https://doi.org/10.1016/j.apenergy.2013.08.085Fuzzy logic based model to predict maximum oil-film pressure in journal bearing
Ahmed, Diyar I., Kasolang, S., Khidhir, Basim A. and Yousif, B. F.. 2013. "Fuzzy logic based model to predict maximum oil-film pressure in journal bearing." Research Journal of Applied Sciences, Engineering and Technology. 6 (20), pp. 3871-3878.Thermal degredation study of kenaf fibre/epoxy composites using thermo gravimetric analysis
Azwa, Z. N. and Yousif, B. F.. 2013. "Thermal degredation study of kenaf fibre/epoxy composites using thermo gravimetric analysis." 3rd Malaysian Postgraduate Conference (MPC 2013). Sydney, Australia 04 - 05 Jul 2013 Sydney, Australia.The air fuel ratio study for the mixture of biogas and hydrogen on mild combustion
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "The air fuel ratio study for the mixture of biogas and hydrogen on mild combustion." 3rd Malaysian Postgraduate Conference (MPC 2013). Sydney, Australia 04 - 05 Jul 2013 Sydney, Australia.Discretization of three dimensional non-uniform grid: conditional moment closure elliptic equation using finite difference method
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2013. "Discretization of three dimensional non-uniform grid: conditional moment closure elliptic equation using finite difference method." 3rd Malaysian Postgraduate Conference (MPC 2013). Sydney, Australia 04 - 05 Jul 2013 Sydney, Australia.A homogeneous charge compression ignition engine: an introduction
Hairuddin, A. Aziz, Wandel, Andrew P. and Yusaf, Talal. 2013. "A homogeneous charge compression ignition engine: an introduction." 3rd Malaysian Postgraduate Conference (MPC 2013). Sydney, Australia 04 - 05 Jul 2013 Sydney, Australia.Adhesive wear characteristics of natural fiber-reinforced composites
Yousif, Belal F.. 2012. "Adhesive wear characteristics of natural fiber-reinforced composites." Davim, J. Paulo (ed.) Wear of advanced materials. London, United Kingdom. John Wiley & Sons. pp. 61-97The potential of using date palm fibres as reinforcement for polymeric composites
Alsaeed, T., Yousif, B. F. and Ku, H.. 2013. "The potential of using date palm fibres as reinforcement for polymeric composites." Materials and Design. 43, pp. 177-184. https://doi.org/10.1016/j.matdes.2012.06.061Tensile properties of bagasse reinforced epoxy composites
Trada, M., Mandava, J., Ku, H. and Yousif, B.. 2012. "Tensile properties of bagasse reinforced epoxy composites." Jaafar, M., Azura, A. R., Leong, K. H. and Leong, A. Y. L. (ed.) 8th Asian-Australasian Conference on Composite Materials (ACCM 2012): Composites: Enabling Tomorrow's Industry Today. Kuala Lumpur, Malaysia 06 - 08 Nov 2012 Kowloon, Hong Kong.Implementing multimedia resources in online learning and its effect on student understanding
Yousif, B. F., Basson, Marita and Hobohm, Carola. 2012. "Implementing multimedia resources in online learning and its effect on student understanding." Mann, Llewellyn and Daniel, Scott (ed.) 23rd Annual Conference of the Australasian Association for Engineering Education (AAEE 2012). Melbourne, Australia 03 - 05 Dec 2012 Melbourne, Australia.Tribological consideration in roller mill machines for agriculture applications
Al-Sandooq, J. M., Yousif, B. F. and Jensen, T. A.. 2012. "Tribological consideration in roller mill machines for agriculture applications." Surface Review and Letters. 19 (6), pp. 1250065-1. https://doi.org/10.1142/S0218625X12500655Characteristics of kenaf fibre immersed in different solutions
Yousif, B. F., Orupabo, C. and Azwa, Z. N.. 2012. "Characteristics of kenaf fibre immersed in different solutions." Journal of Natural Fibers. 9 (4), pp. 207-218. https://doi.org/10.1080/15440478.2012.733149Epoxy composite based on kenaf fibers for tribological applications under wet contact conditions
Yousif, B. F. and Chin, C. W.. 2012. "Epoxy composite based on kenaf fibers for tribological applications under wet contact conditions." Surface Review and Letters. 19 (5), pp. 1250050-1. https://doi.org/10.1142/S0218625X12500503Suitability of using coir fiber/polymeric composite for the design of liquid storage tanks
Yousif, B. F. and Ku, H.. 2012. "Suitability of using coir fiber/polymeric composite for the design of liquid storage tanks." Materials and Design. 36, pp. 847-853. https://doi.org/10.1016/j.matdes.2011.01.063The synergistic effect of hybrid flame retardants on pyrolysis behaviour of hybrid composite materials
Albdiry, M. T., Almosawi, A. I. and Yousif, B. F.. 2012. "The synergistic effect of hybrid flame retardants on pyrolysis behaviour of hybrid composite materials." Journal of Engineering Science and Technology. 7 (3), pp. 351-359.Tribo performance of T-BFRP composite subjected to dry/wet contact conditions
Nirmal, Umar, Hashim, Jamil, Rilling, Dirk, Brevern, P. V. and Yousif, B. F.. 2012. "Tribo performance of T-BFRP composite subjected to dry/wet contact conditions." Francis, Elizabeth (ed.) Natural polymers, biopolymers, biomaterials, and their composites, blends, and IPNs. Toronto, Canada. Apple Academic Press (CRC Press). pp. 311-325Flexural properties of treated and untreated kenaf/epoxy composites
Yousif, B. F., Shalwan, A., Chin, C. W. and Ming, K. C.. 2012. "Flexural properties of treated and untreated kenaf/epoxy composites." Materials and Design. 40, pp. 378-385. https://doi.org/10.1016/j.matdes.2012.04.017Investigating the efficiency of ultrasound for controlling bio-fouling in batch membrane systems
Yusaf, T. F. and Al-Juboori, Raed Ahmed. 2012. "Investigating the efficiency of ultrasound for controlling bio-fouling in batch membrane systems ." Noor, M. M., Baker, Paul and Yusaf, Talal F. (ed.) USQ Combustion Meeting 2012 (21st November). Toowoomba, Australia 21 Nov 2012 Toowoomba, Australia.The use of microalgae biodiesel in diesel engine: production, extraction and engine performance
Yusaf, T. F. and Al-lwayzy, Saddam H.. 2012. "The use of microalgae biodiesel in diesel engine: production, extraction and engine performance." Noor, M. M., Baker, Paul and Yusaf, Talal F. (ed.) USQ Combustion Meeting 2012 (21st November). Toowoomba, Australia 21 Nov 2012 Toowoomba, Australia.A review of mild combustion and open furnace design consideration
Noor, M. M., Wandel, Andrew P. and Yusaf, Talal. 2012. "A review of mild combustion and open furnace design consideration." International Journal of Automotive and Mechanical Engineering. 6 (1), pp. 730-754.Fibre composite railway sleeper design by using FE approach and optimization techniques
Awad, Ziad K. and Yusaf, Talal. 2012. "Fibre composite railway sleeper design by using FE approach and optimization techniques." Structural Engineering and Mechanics. 41 (2), pp. 231-242. https://doi.org/10.12989/sem.2012.41.2.231Artificial neural networks approach for the prediction of thermal balance of SI engine using ethanol-gasoline blends
Kiani, Mostafa Kiani Deh, Ghobadian, Barat, Ommi, Fathollah, Najafi, Gholamhassan and Yusaf, Talal. 2012. "Artificial neural networks approach for the prediction of thermal balance of SI engine using ethanol-gasoline blends." Quirchmayr, Gerald, Basl, Josef, You, Ilsun, Xu, Lida and Weippl, Edgar (ed.) 2012 International Cross-Domain Conference and Workshop on Availability, Reliability, and Security (CD-ARES 2012). Prague, Czech Republic 20 - 24 Aug 2012 Berlin, Germany. https://doi.org/10.1007/978-3-642-32498-7_3Design of newly fabricated tribological machine for wear and frictional experiments under dry/wet condition
Yousif, B. F.. 2013. "Design of newly fabricated tribological machine for wear and frictional experiments under dry/wet condition." Materials and Design. 48, pp. 2-13. https://doi.org/10.1016/j.matdes.2012.06.046Betelnut fibres as an alternative to glass fibres to reinforce thermoset composites: a comparative study
Nirmal, Umar, Hashim, Jamil, Lau, Saijod T. W., Yuhazri, M. Y. and Yousif, B. F.. 2012. "Betelnut fibres as an alternative to glass fibres to reinforce thermoset composites: a comparative study." Textile Research Journal. 82 (11), pp. 1107-1120. https://doi.org/10.1177/0040517512439945Morphological structures and tribological performance of unsaturated polyester based untreated/silane-treated halloysite nanotubes
Albdiry, M. T. and Yousif, B. F.. 2013. "Morphological structures and tribological performance of unsaturated polyester based untreated/silane-treated halloysite nanotubes." Materials and Design. 48, pp. 68-76. https://doi.org/10.1016/j.matdes.2012.08.035HCCI engine: numerical and experimental approach
Hairuddin, A. Aziz, Yusaf, Talal F. and Wandel, Andrew P.. 2012. "HCCI engine: numerical and experimental approach." Noor, M. M., Baker, Paul and Yusaf, Talal F. (ed.) USQ Combustion Meeting 2012 (26th September). Toowoomba, Australia 26 Sep 2012 Toowoomba, Australia.A critical review on the manufacturing processes in relation to the properties of nanoclay/polymer composites
Albdiry, M. T., Yousif, B. F., Ku, H. and Lau, K. T.. 2013. "A critical review on the manufacturing processes in relation to the properties of nanoclay/polymer composites." Journal of Composite Materials. 47 (9), pp. 1093-1115. https://doi.org/10.1177/0021998312445592Investigation of Biogas Moderate or Intense Low Oxygen Dilution (MILD) combustion on open furnace bluff-body burner
Noor, M. M., Wandel, Andrew P. and Yusaf, T. F.. 2012. "Investigation of Biogas Moderate or Intense Low Oxygen Dilution (MILD) combustion on open furnace bluff-body burner." Noor, M. M., Baker, Paul and Yusaf, Talal F. (ed.) USQ Combustion Meeting 2012 (29th August). Toowoomba, Australia 29 Aug 2012 Toowoomba, Australia.Modelling of non-premixed turbulent combustion of hydrogen using conditional moment closure method
Noor, M. M., Hairuddin, A. Aziz, Wandel, Andrew P. and Yusaf, T. F.. 2012. "Modelling of non-premixed turbulent combustion of hydrogen using conditional moment closure method." IOP Conference Series: Materials Science and Engineering. 36 (1), pp. 1-17. https://doi.org/10.1088/1757-899X/36/1/012036The modelling of the effect of air fuel ratio on unburned hydrocarbons for MILD combustion
Noor, M. M., Wandel, Andrew P. and Yusaf, T. F.. 2012. "The modelling of the effect of air fuel ratio on unburned hydrocarbons for MILD combustion." Noor, M. M., Rahman, M. M. and Ismail, J. (ed.) 2nd Malaysian Postgraduate Conference (MPC 2012). Gold Coast, Australia 07 - 09 Jul 2012 Sydney, Australia.A preliminary study of control parameters for open furnace mild combustion using CFD
Noor, M. M., Wandel, Andrew P. and Yusaf, T. F.. 2012. "A preliminary study of control parameters for open furnace mild combustion using CFD." Noor, M. M., Rahman, M. M. and Ismail, J. (ed.) 2nd Malaysian Postgraduate Conference (MPC 2012). Gold Coast, Australia 07 - 09 Jul 2012 Sydney, Australia.Mild combustion: a technical review towards open furnace combustion
Noor, M. M., Wandel, Andrew P. and Yusaf, T. F.. 2012. "Mild combustion: a technical review towards open furnace combustion." Noor, M. M., Rahman, M. M. and Ismail, J. (ed.) 2nd Malaysian Postgraduate Conference (MPC 2012). Gold Coast, Australia 07 - 09 Jul 2012 Sydney, Australia.Numerical investigation of influence of air and fuel dilution for open furnace MILD combustion burner
Noor, M. M., Wandel, Andrew P. and Yusaf, T. F.. 2012. "Numerical investigation of influence of air and fuel dilution for open furnace MILD combustion burner." 2012 Southern Regional Engineering Conference (SREC 2012). Toowoomba, Australia 01 Sep 2012 Canberra, Australia.Numerical investigation of flow instability in shock tube due to shock wave-contact surface interactions
Al-Falahi, Amir, Yusoff, M. Z., Yusaf, Talal and Ahmed, Diyar I.. 2012. "Numerical investigation of flow instability in shock tube due to shock wave-contact surface interactions." International Journal of Numerical Methods for Heat and Fluid Flow. 22 (3), pp. 377-398. https://doi.org/10.1108/09615531211208079Biofouling in RO system: mechanisms, monitoring and controlling
Al-Juboori, Raed A. and Yusaf, Talal. 2012. "Biofouling in RO system: mechanisms, monitoring and controlling." Desalination. 302, pp. 1-23. https://doi.org/10.1016/j.desal.2012.06.016Identifying the optimum process parameters for ultrasonic cellular disruption of e. coli
Al-Juboori, Raed A. and Yusaf, Talal. 2012. "Identifying the optimum process parameters for ultrasonic cellular disruption of e. coli ." International Journal of Chemical Reactor Engineering. 10 (1), pp. 1-32. https://doi.org/10.1515/1542-6580.2937Predicting the combustion behaviour of a diesel HCCI engine using a zero-dimensional single-zone model
Hairuddin, A. Aziz, Yusaf, Talal F. and Wandel, Andrew P.. 2011. "Predicting the combustion behaviour of a diesel HCCI engine using a zero-dimensional single-zone model." Kennedy, Eric, Dlugogorski, Bogdan, Moghtaderi, Behdad and Masri, Assaad (ed.) 11th Australian Combustion Symposium (ACS 2011). Newcastle, Australia 29 Nov - 01 Dec 2011 Sydney, Australia.![](/~234/dnn/default-thumbnail.png)